User manual ARISTO AM-650BX-S

[. . . ] 1 Electronic Emission Notices Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions contained in this manual, may cause harmful interference to radio and television communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Celeron PGA370 CPU is frequency multiplier locked, no CPU speed change will be seen even if the frequency multiplier setting in CMOS setup is changed. JP1 - Host Bus Speed Select JP1 1 1 JP3 - CMOS Clear JP3 (1-2)* (2-3) JP28 - Keyboard Power on Password Clear JP28 (1-2)* (2-3) JP29 (1-2)* (2-3) JP29, JP30, JP31 - Sound Chip Enable Setting 1 1 1 1 * = Default setting. Technical Reference Booklet JP29 JP30 JP31 1 JP9 1 (Close)* (Open) 1 1 JP3 1 JP28 1 JP15 1 JP8 1 HCLK Auto* 100 MHz JP1 1 Selection Normal* CMOS Clear Selection Normal* Clear Keyboard Power on Password JP30 (1-2)* (2-3) JP31 (1-2)* (2-3) Selection Enable* Disable Close Open 1 1 7 JP9 - Keyboard Power Select JP9 (1-2)* (2-3) Selection Powered by +5V* Powered by +5V Standby Keyboard Password Power on This motherboard provides a special security feature of keyboard password power on. The feature is enabled in integrated peripherals menu of CMOS setup. (1) single Key Turn on - if you set a single key password, the system will turn on immediately after you press the password key. (2) Keys Sequence Turn on - if you set a password with more than one character, ie. a combination of keys, the system will turn on after you press the password key sequence and then a <enter>. Please notice that the power button will have no function if the keyboard password power on feature is enabled. JP8, JP15 - BIOS Program Voltage / BIOS Select JP8 (1-2) (1-2) (2-3) (2-3) JP15 1 1 1 1 Selection (1-2) (2-3) (2-3) (2-4) INTEL (1MB) MX (1MB) ATMEL/SST/Winbond (1MB) ATMEL/SST/Winbond (2MB) JP8 & JP15 are pre-installed in the factory. They should NOT be altered by the users. * =Default setting Close Open Hardware Setup 8 Pin List of Special Connectors: 1. CN8: PS/2 Mouse 1 5 1 3 5 7 VCC USBP1USBP1+ GND 2 4 6 8 GND USBP0+ USBP0VCC 1 2 3 4 5 VCC NC MS_DATA GND MS_CLK 3. CN25: CD-IN(JST) 1 4 1 1 2 3 4 GND CD-L GND CD-R 1 2 3 4 CD-L GND GND CD-R 5. CN16: INFRA-RED 1 4 1 2 3 4 AUX-L GND GND AUX-R 1 2 3 4 IRRX GND IRTX VCC Technical Reference Booklet 9 Installation Installing the Processor Unpack the CPU and identify the pin 1 corner of the CPU. Match pin 1 of the CPU with pin 1 of the CPU socket. The pin 1 corner of the CPU socket is designated by a small triangle printed on the motherboard. Carefully insert the CPU into the CPU socket and move the metal arm downward to replace it in its original position. Change any jumper settings as detailed in the manual. If a heat sink is attached and covers the top of the CPU, identify the pin 1 corner by turning the CPU over. Locate the small gold finger that extends from one corner of the large central square portion of the CPU. The gold finger points towards pin 1, which is also uniquely identified by a square pad. Installing DIMMs 1. Turn off all peripheral devices connected to the computer. Remove the computer cover and locate the DIMM sockets. Holding the DIMM by the edges, remove it from its antistatic package. Make sure the clips at either end of the socket are pushed away from the socket. Clip DIMM Clip DIMM Socket Notch 5. Align the two small notches in the bottom edge of the DIMM with the keys in the socket. Insert the bottom edge of the DIMM into the socket. When the DIMM is seated, push down on the top edge of the DIMM until the retaining clips at the ends of the socket snap into place. [. . . ] This section covers some very technical items and it is recommended that only experienced users should make any changes to the default settings. Integrated Peripherals The Integrated Peripherals Setup allows the user to configure the onboard IDE controller, floppy disk controller, the printer port and the serial ports. Supervisor/User Password Setting You can set either supervisor or user password, or both of them. The difference between them are: Supervisor Password : You can enter the Setup Program and change the options of the setup menus. User Password : You can enter the Setup Program but cannot change the options of the setup menus. When you select this function, the following message will appear at the center of the screen to assist you in creating a password. BIOS Setup 16 ENTER PASSWORD: Type the password, up to eight characters in length, and press<Enter>. The new password will clear the previously entered password from the CMOS memory. You will be asked to confirm the password. [. . . ]