User manual ARISTO AM-672

[. . . ] 1 Electronic Emission Notices Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions contained in this manual, may cause harmful interference to radio and television communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] 1) Single Key Turn On - if you set a single key password, the system will turn on immediately after you press the password key. 2) Keys Sequence Turn On - if you set a password with more than one character, ie. a combination of keys, the system will turn on after you press the password key sequence and then a <enter>. Pin Assignment Interinal Audio Connector CN16 : Infrared Module 1 Pin 1 2 3 4 Assignment IRRX GND IRTX VCC CN25 : AUX-IN Pin 1 2 3 4 Assignment AUX-L GND GND AUX-R Assignment CD-L GND GND CD-R Assignment CD-R GND CD-L GND CN24 : CD-IN 1 Pin 1 2 3 4 Pin 1 2 3 4 CN31 : CD-IN RGLG CN32 : CD-IN Pin 1 2 3 4 Assignment GND CD-L GND CD-R Close Open GLGR * = Default setting. Hardware Configuration 8 Installing WIN®9x Driver for Intel® 810/810E/810DC100 Chipset Products Installing Procedures 1) With no peripheral cards installed, power up and press <Del> key to go into CMOS Setup. Load the "Optimized" Default in CMOS, save and exit. Reboot, format the hard disk drive and install a fresh Windows Operating System. The Windows source files may be from the Microsoft CD-ROM disk, or from another HDD partition depending on user preference. When Windows is up and running in Standard VGA Mode, insert the CD-ROM Disk bundled with the 810 chipset motherboard into the CD-ROM drive. Installation of USB Supplement for Win95 (OSR2) : * This is only needed for Win95, because Win98 already included the USB support. If you are using Win98, please skip this step. 4-1) Locate the following subdirectory from the bundled CD-ROM : \Intel Chipset Products\810\USB_Supplement\ 4-2) Run Usbsupp. exe, and follow the instruction on screen. 8-A1) Locate the following subdirectory from the bundled CD-ROM : \Intel Chipset Products\810\PCI_Sound\Crystal Chipset\ 8-A2) Select the operating system (win95, win98, . . . ) 8-A3) Run Setup. exe, and follow the instruction on screen. 8-A4) Restart computer to let the driver take effect. 8-A5) When prompted for new device driver path, specify the PCI_Sound installation source path, either from CD-ROM, or from Floppy, or from HDD, in accordance with your installation media. B) Installation of On-Board PCI Sound (Creative ES1373) Sound Driver : * This is only applicable for motherboards with Creative ES1373 Sound Chip. 8-B1) Locate the following subdirectory from the bundled CD-ROM : \Intel Chipset Products\810\PCI_Sound\Creative Chipset\ 8-B2) Run Setup. exe, and follow the instruction on screen. 8-B3) Restart computer to let the driver take effect. 8-B4) When prompted for new device driver path, specify the PCI_Sound installation source path, either from CD-ROM, or from Floppy, or from HDD, in accordance with your installation media. 9) Installation of On-Board AC97 Codec Sound Driver : * This is only applicable for motherboards with On-Board AC97 Codec Sound function. 9-1) Locate the following subdirectory from the bundled CD-ROM : \Intel Chipset Products\810\AC97 Sound\ 9-2) Indentify which brand of "AC97 Codec IC" is implemented on your 810 motherboard, and specify the subdirectory under the above path location. 9-3) Select the operating system (Win9x in this case), run Setup. exe, and follow the instruction on screen. 9-4) Restart computer to let the driver to take effect. 8) 10) Examine the Windows Device Manager, to confirm that all the drivers are properly installed -> Control Panel/System/Device Manager. 11 ) Turn power off to proceed with installation of other peripheral cards, eg. [. . . ] The new password will clear the previously entered password from the CMOS memory. You will be asked to confirm the password. Type the password again and press <Enter>. You may also press <Esc> to abort the selection and operate without a password. [. . . ]