User manual ARISTO AM-726V33

[. . . ] ii Contents Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Unpacking the Mainboard & Static Electricity Precautions. . . . . 4 Chapter 2: Hardware Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] For example, you may ground yourself by grasping an unpainted portion of the systems metal chassis. Remove the mainboard from its anti-static packaging and place it on a grounded surface, component side up. Handle the mainboard by its edges or by the mounting bracket to avoid touching its components. If any integrated circuit appears loose, press carefully to seat it firmly in its socket. Do not apply power if the mainboard appears damaged. If there is damage to the board contact your dealer immediately. 3. 4. 5. 6. Chapter 2 Hardware Configuration Before you install the mainboard into the system chassis, you may find it convenient to first configure the mainboards hardware. This chapter describes how to set jumpers and install memory modules, and where to attach components. 6 Chapter 2 CPU Installation This mainboard supports Intel Pentium II CPU using a Single Edge Contact (SEC) slot. Make sure that you have the following items (which should be included in the package) before doing any installation. All parts are labeled here with item numbers which will be refered to in the Installation Procedures section. Item 1 and 2 together are the retention mechanism, please refer to following procedures to complete your CPU installation. 1) 4 screws: 2) 1 retention clip: Hardware Configuration 9 Step 4: And then simply push the screws downward to secure the the retention clip. Push in to secure. Step 5: Flatten the two latches on the side of CPU. Lock the two latches to secure the CPU. Hardware Configuration 11 Connectors Attach system components and case devices to the mainboard via the mainboard connectors. A description of each connector pins follows. See Figure 21 for the location of the connectors on the mainboard. Note: Make sure that the power is turned off before making any connection to the board. PWR1 AT Power Connector COM1/2 Serial Port #1/#2 PRN1 Parallel Printer Connector FDC1 Floppy Disk Drive Connector IDE1/IDE2 Primary/Secondary IDE Connectors KBD1 Keyboard Connector J2 ATX Form Card Connector This connector contains 2 sets of USB interface, PS/2 Mouse, and Infrared connectors. Connect the ATX Form Card cable to this connector. 12 Chapter 2 J4 (2, 4, 6, 8, 10) (KEYLOCK) Keylock & Power LED Connector Keylock connector enables and disables the keyboard key-in function on the case. Pin 2 4 6 8 10 Description LED Output N. C. Ground Keylock Ground J4 (1, 3, 5, 7) (SPK) Speaker Connector Pin 1 3 5 7 Description Data Out N. C. Ground +5V J4 (13, 14) (TB-LED) Turbo LED Connector Pin 13 (+) 14 () Description +5V Active Low Hardware Configuration 13 J4 (15, 16) (HDD-LED) HDD LED Connector Pin 15 (+) 16 () Description +5V Active Low J4 (17, 18) (RST) Reset Switch Connector Setting Open Close Description Normal Mode Reset System J4 (19, 20) (SPDLED) Suspend LED Connector Pin 19 (+) 20 () Description +5V Active Low FAN-P/FAN-C Processor/Case Fan Connector Sound Pro Connectors: CD1/CD2 Analog Audio for Panasonic/Sony Connect to AUDIO on the CD-ROM drive, and the signal for Panasonic jack is G-S-G-S and S-G-G-S for Sony. 14 Chapter 2 J3 Sound and Game Sound contains Line-in/MIC (Microphone), and Lineout (Speaker). Game connector is also the Joystic connector. Connect this connector to the Sound & Game ribbon cable/bracket as the following drawing: Line-In MIC Line-Out Game J3 J3 JP6 Digital Audio IN Depending on the type of your CD-ROM drive to connect this connector to DIGITAL AUDIO on the CD-ROM drive by using the SPDIF/IN cable. JP7 Digital Audio OUT By using the optional SPDIF/OUT cable/barcket, you can connect the digital audio devices such as external audio amplifier or minidisk. Hardware Configuration 15 Jumper Settings JP1 DIMM Voltage Selectors Voltage 3. 3V Setting AB 3V 5V AB 5V 3V 5V JP3 Microphone Type Selector Description Standard (default) Special Setting JP8 Onboard Sound Pro Selector Description Enabled (default) Disabled Setting 1 1 Hardware Configuration 17 Memory Installation The mainboard lets you add up to 768MB of system memory. Three 168-pin DIMM sockets are divided into three banks: Bank 0, Bank 1, and Bank 2. [. . . ] Standby Time out This option specified the length of system (Minute) inactivity while in Full power on state. When this length of time expires, the computer enters Standby power state. Suspend Time out This option specified the length of a period of (Minute) system inactivity while in Standby state. When this length of time expires, the computer enters Suspend power state. [. . . ]