User manual ARISTO AM-924

[. . . ] 1 Electronic Emission Notices Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions contained in this manual, may cause harmful interference to radio and television communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: REORIENT OR RELOCATE THE RECEIVING ANTENNA INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM THAT OF THE RECEIVER CONSULT THE DEALER OR AN EXPERIENCED AUDIO/TELEVISION TECHNICIAN NOTE: Connecting this device to peripheral devices that do not comply with Class B requirements, or using an unshielded peripheral data cable, could also result in harmful interference to radio or television reception. [. . . ] Celeron PGA370 CPU is frequency multiplier locked, no CPU speed change will be seen even if the frequency multiplier setting in CMOS setup is changed. JP1, JP2 - System Bus Frequency JP1 1 1 1 Open Open Close* JP34 - On Board Crystal PCI Sound (Optional) JP34 1-2* 2-3 Function PCI Sound Enable* PCI Sound Disable JP35, JP36 - On Board AC97 Codec Sound JP35 1-2* 2-3 JP36 2-3* (S)# 1-2 (P)# Function AC97 Sound Enable* AC97 Sound Disable JP15 - BIOS (Firm Ware Hub) Boot Block Protect JP15 1 1 Close* Open Technical Reference Booklet 1 JP1 JP2 JP2 1 Open 1-2 1-2* CPU Clock Speed 133MHz (100MHz CPU run at 133MHz Front Side Bus) 100MHz (66MHz CPU run at 100MHz Front Side Bus) Auto* JP4 - CMOS Clear JP4 1-2* 2-3 Function Normal* CMOS Clear Function Unlocked* Locked # P = Primary AMR, S = Secondary AMR 7 JP29 - Keyboard Power On Select JP29 1-2* 2-3 Function Powered by +5V* Powered by +5V Standby (Allows Keyboard Power On) Keyboard Password Power On This motherboard provides a special security feature of keyboard password power on. The feature is enabled in Integrated Peripherals Menu of CMOS setup. 1) Single Key Turn On - if you set a single key password, the system will turn on immediately after you press the password key. 2) Keys Sequence Turn On - if you set a password with more than one character, ie. a combination of keys, the system will turn on after you press the password key sequence and then a <enter>. Pin Assignment Interinal Audio Connector CN25 : AUX-IN 1 Pin 1 2 3 4 Assignment AUX-L GND GND AUX-R CN16 : Infrared Module 1 Pin 1 2 3 4 Assignment IRRX GND IRTX VCC CN24 : CD-IN 1 Pin 1 2 3 4 Pin 1 2 3 4 Pin 1 2 3 4 Assignment CD-L GND GND CD-R Assignment CD-R GND CD-L GND Assignment GND CD-L GND CD-R CN8 : PS/2 Mouse 1 Pin 1 2 3 4 5 Assignment VCC NC MS-DATA GND MS-CLK CN33 : CD-IN CN7 : USB Port 2 1 8 7 RGLG CN32 : CD-IN GLGR Pin 1 2 3 4 5 6 7 8 Assignment VCC GND USBP1USBP0+ USBP1+ USBP0GND VCC Close Open * = Default setting. Hardware Configuration 8 Installing WIN®9x Driver for Intel® 810/810E/810DC100 Chipset Products Installing Procedures 1) With no peripheral cards installed, power up and press <Del> key to go into CMOS Setup. Load the "Optimized" Default in CMOS, save and exit. Reboot, format the hard disk drive and install a fresh Windows Operating System. The Windows source files may be from the Microsoft CD-ROM disk, or from another HDD partition depending on user preference. 7-3) Restart computer to let the driver take effect. A) Installation of On-Board PCI Sound (Crystal CS4280) Sound Driver : * This is only applicable for motherboards with Crystal CS4280 Sound Chip. 8-A1) Locate the following subdirectory from the bundled CD-ROM : \Intel Chipset Products\810\PCI_Sound\Crystal Chipset\ 8-A2) Select the operating system (win95, win98, . . . ) 8-A3) Run Setup. exe, and follow the instruction on screen. 8-A4) Restart computer to let the driver take effect. 8-A5) When prompted for new device driver path, specify the PCI_Sound installation source path, either from CD-ROM, or from Floppy, or from HDD, in accordance with your installation media. B) Installation of On-Board PCI Sound (Creative ES1373) Sound Driver : * This is only applicable for motherboards with Creative ES1373 Sound Chip. 8-B1) Locate the following subdirectory from the bundled CD-ROM : \Intel Chipset Products\810\PCI_Sound\Creative Chipset\ 8-B2) Run Setup. exe, and follow the instruction on screen. 8-B3) Restart computer to let the driver take effect. 8-B4) When prompted for new device driver path, specify the PCI_Sound installation source path, either from CD-ROM, or from Floppy, or from HDD, in accordance with your installation media. 9) Installation of On-Board AC97 Codec Sound Driver : * This is only applicable for motherboards with On-Board AC97 Codec Sound function. 9-1) Locate the following subdirectory from the bundled CD-ROM : \Intel Chipset Products\810\AC97 Sound\ 9-2) Indentify which brand of "AC97 Codec IC" is implemented on your 810 motherboard, and specify the subdirectory under the above path location. 9-3) Select the operating system (Win9x in this case), run Setup. exe, and follow the instruction on screen. 9-4) Restart computer to let the driver to take effect. 8) 10) Examine the Windows Device Manager, to confirm that all the drivers are properly installed -> Control Panel/System/Device Manager. 11 ) Turn power off to proceed with installation of other peripheral cards, eg. [. . . ] The new password will clear the previously entered password from the CMOS memory. You will be asked to confirm the password. Type the password again and press <Enter>. You may also press <Esc> to abort the selection and operate without a password. [. . . ]