User manual ARISTO AM-960

[. . . ] 1 Electronic Emission Notices Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions contained in this manual, may cause harmful interference to radio and television communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Direct Sound and Sound Blaster compatible. Full-Duplex 16-bit record and play back. Line-in, Line-out, Mic-in and MIDI/Game port. Power Management · · · · · · Supports SMM, APM and ACPI. Break switch for instant suspend/resume on system operations. Energy star "Green PC" compliant. Hardware monitoring circuit is supported, provide voltage, temperature, fan speed, etc. External Modem Ring-in Wake-up support. Expansion Slots · · · 1 AMR slot. 2. 1 compliant. CAUTION Static electricity can harm delicate components of the motherboard. To prevent damage caused by static electricity, discharge the static electricity from your body before you touch any of the computers electronic components. Technical Reference Booklet 5 Motherboard Layout (Model Code No. - 35C96000XX) The following diagrams show the relative positions of the jumpers, connectors, major components and memory banks on the motherboard. 1 NOTE 1) 2) Be sure to check the cable orientation in order to match the colored strip to the pin 1 end of the connector. When you start up the system, please wait for 5 seconds after you power on AC. Hardware Configuration 6 Jumper Settings This chapter explains how to configure the motherboard's hardware. Before using your computer, make sure all jumpers and DRAM modules are set correctly. Refer to this chapter whenever in doubt. JVSB1 JBAT 1 CPU Speed Selection In this motherboard, jumperless feature is implemented such that no jumper is required to be set for different type of CPU installed. Be sure to save the CMOS setting when exit the CMOS. The CPU is frequency multiplier locked, no CPU speed change will be seen even if the frequency multiplier setting in CMOS setup is changed. CK1, CK4 - System Bus Frequency CK1 1 1 1 EDS1, JP42 - On Board AC97 Codec Sound & AMR Setting EDS1 2-3* 1-2 JP42 2-3* (S)# 1-2 (P)# Function AC97 Sound Enable* AC97 Sound Disable JBAT - CMOS Clear JBAT 1-2* 2-3 Selection Normal* CMOS Clear JVSB1 - Keyboard Power Select JVSB1 2-3* 1-2 Select Powered by +5V* Powered by +5V Standby (Allows Keyboard Power On) Technical Reference Booklet JP42 EDS1 CK4 Open Open Close* 1 1 1 1 1 CK4 CK1 CPU Clock Speed 133MHz 100MHz Auto* Open Close Close* # P = Primary AMR, S = Secondary AMR Close Open * = Default setting. 7 Pin Assignment Internal Audio Connector AUX1 : AUX-IN 1 Pin 1 2 3 4 Pin 1 2 3 4 Assignment AUX-L GND GND AUX-R Assignment CD-L GND GND CD-R CDS2 : CD-IN Pin 1 2 3 4 Assignment CD-R GND CD-L GND RGLG CDS1 : CD-IN 1 CDS3 : CD-IN Pin 1 2 3 4 Assignment GND CD-L GND CD-R GLGR FP1 FRONT PANEL HEADER HEADER 2x12 PWR+ GND PWRLED+ PWRLEDHDDLED+ HDDLEDRST+ GND SPEAK GND VCC 1 3 5 7 9 11 13 15 17 19 21 23 +PWR - SW +PWR - LED +HDD - LED +RST - SW S NC + SUS+ SW RX TX + + NC S IrDA 2 4 6 8 10 12 14 16 18 20 22 24 SUS+ GND IRRX GND IRTX VCC KEYLOCK+ X X GND KEYLOCKGND X SPKER KEYLOCK Hardware Configuration 8 Hardware Setup To Install DIMMs 1. Holding the DIMM by the edges, remove it from its antistatic package. Make sure the clips at either end of the socket are pushed away from the socket. Align the two small notches in the bottom edge of the DIMM with the keys in the socket. Insert the bottom edge of the DIMM into the socket. When the DIMM is seated, push down on the top edge of the DIMM until the retaining clips at the ends of the socket snap into place. Make sure the clips are firmly in place. Turn system power off before installing and removing any device, otherwise you'll cause the system damage. Technical Reference Booklet 9 Installing a New Processor An upgrade processor can dramatically increase general system speed and performance. Most microprocessor upgrade kits include the following items: · Microprocessor chip · Installation instructions and technical data Your system may have these features built in, or support them as upgrades. To Install a Processor to ZIF Socket To install the processor, follow these steps: 1. [. . . ] The new password will clear the previously entered password from the CMOS memory. You will be asked to confirm the password. Type the password again and press <Enter>. You may also press <Esc> to abort the selection and operate without a password. [. . . ]