User manual ARISTO AM-993

[. . . ] 1 Electronic Emission Notices Federal Communications Commission (FCC) Statement (00399C) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions contained in this manual, may cause harmful interference to radio and television communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Be sure to save the CMOS setting when exit the CMOS. The CPU is frequency multiplier locked, no CPU speed change will be seen even if the frequency multiplier setting in CMOS setup is changed. CK1, CK4 - System Bus Frequency CK1 1 1 1 EDS1 - On Board AC97 Codec Sound EDS1 2-3* 1-2 Function AC97 Sound Enable* AC97 Sound Disable JBAT - CMOS Clear JBAT 1-2* 2-3 Selection Normal* CMOS Clear JVSB1 - Keyboard Power Select JVSB1 2-3* 1-2 Select Powered by +5V* Powered by +5V Standby (Allows Keyboard Power On) Technical Reference Booklet EDS1 CK4 Open Open Close* 1 1 1 1 CK4 CK1 CPU Clock Speed 133MHz 100MHz Auto* Open Close Close* Close Open * = Default setting. 7 Pin Assignment Internal Audio Connector AUX1 : AUX-IN 1 Pin 1 2 3 4 Pin 1 2 3 4 Assignment AUX-L GND GND AUX-R Assignment CD-L GND GND CD-R CDS2 : CD-IN Pin 1 2 3 4 Assignment CD-R GND CD-L GND RGLG CDS1 : CD-IN 1 CDS3 : CD-IN Pin 1 2 3 4 Assignment GND CD-L GND CD-R GLGR FP1 FRONT PANEL HEADER HEADER 2x12 GND KEYLOCKGND KEYLOCK+ VCC IRTX GND IRRX GND SUS+ 24 22 20 18 16 14 12 10 8 6 4 2 X X S NC + + TX RX + NC S SW RST+ 23 21 19 17 15 13 11 9 7 5 3 1 VCC GND - SW +SUS KEYLOCK IrDA SPKER X SPEAK GND RST+ HDDLEDHDDLED+ PWRLEDPWRLED+ GND PWR+ LED HDD+ LED PWR+ SW PWR+ Hardware Configuration 8 Hardware Setup To Install DIMMs 1. Holding the DIMM by the edges, remove it from its antistatic package. Make sure the clips at either end of the socket are pushed away from the socket. Align the two small notches in the bottom edge of the DIMM with the keys in the socket. Insert the bottom edge of the DIMM into the socket. When the DIMM is seated, push down on the top edge of the DIMM until the retaining clips at the ends of the socket snap into place. Make sure the clips are firmly in place. Turn system power off before installing and removing any device, otherwise you'll cause the system damage. Technical Reference Booklet 9 Installing a New Processor An upgrade processor can dramatically increase general system speed and performance. Most microprocessor upgrade kits include the following items: · Microprocessor chip · Installation instructions and technical data Your system may have these features built in, or support them as upgrades. To Install a Processor to ZIF Socket To install the processor, follow these steps: 1. By pressing the <Del> key when the following message appears briefly at the bottom of the screen during the POST (Power On Self Test ) Press DEL to enter SETUP If the message disappears before you can respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the "RESET" button on the system case. You may also restart by simultaneously pressing the <Ctrl>, <Alt>, and <Delete> keys. If you do not press the keys at the correct time and the system does not reset, an error message will be displayed and you will again be asked to . . . PRESS F1 TO CONTINUE, DEL TO ENTER SETUP Getting Help Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press <Esc> or the F1 key again. In Case of Problems If, after making and saving system changes with the Setup Program, you discover that your computer does not reset, use the Award BIOS defaults to override the CMOS settings. Technical Reference Booklet 11 Main Menu Once you enter the Award BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from various setup functions and two exit choices. Use the arrow keys to select among the items and press <Enter> to accept and enter the sub-menu. CMOS Setup Utility - Copyright (C) 1984-2000 Award Software 8 8 8 8 8 8 8 Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status 8 Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving éêèç : Select Item Esc : Quit F10 : Save & Exit Setup Time, Date, Hard Disk Type . . . (Note : The figures of BIOS Setup Menu included here only show a typical case, and may not be exactly the same as the one on your unit. ) Note that a brief description of each highlighted item will appear at the bottom of the screen. Standard This setup page includes all the items of AwardTM specia standard CMOS Features features. Advanced BIOS Features This setup page includes all the items of AwardTM specia enhanced features. Advanced This setup page includes all the items of chipset special features. Chipset Features Integrated Peripherals Power Management Setup PNP/PCI Configurations This section page includes all the items of IDE hard drive and Programmed Input / Output features. This entry only appears if your system supports Power Management "Green PC" standards. This entry appears if your system supports PNP/PCI. PC Health Status Display CPU and Case Fan Speed. Frequency/ CPU speed setting are settings of CPU speed. [. . . ] 4-3) Restart computer to let the driver take effect. Installation of Intel 815/815E/815P/815EP Chipset Update INF Drivers : 5-1) Locate the following subdirectory from the bundled CD-ROM : D:\Intel Chipset Products\815-(815E)\INF_install\disk1\ 5-2) Run Setup. exe, and follow the instruction on screen. 5-3) Restart computer to let the driver take effect. Installation of Intel 815/815E/815P/815EP Ultra ATA Driver (Win98 or above only) : 6-1) Locate the following subdirectory from the bundled CD-ROM : D:\Intel Chipset Products\815-(815E)\ATA Driver\ 6-2) Run Setup. exe, and follow the instruction on screen. [. . . ]