Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ARROW VN108-A. We hope that this ARROW VN108-A user guide will be useful to you.
Lastmanuals help download the user guide ARROW VN108-A.
Detailed instructions for use are in the User's Guide.
[. . . ] Owner's Manual & Assembly Instructions
A01
Model No. EN108-A NP108 SA108-A
HM108-A NW108-A VN108-A
MN108-A PD108-A
709291207
BUILDING DIMENSIONS * Size rounded off to the nearest foot
CAUTION: SOME PARTS HAVE SHARP EDGES. CARE MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ SAFETY INFORMATION PROVIDED IN THIS MANUAL BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES WHEN HANDLING METAL PARTS.
*Approx. [. . . ] Fill up to 4" (10cm) in the square with gravel and tamp firm. Cover gravel with a sheet of 6 mil plastic. Construct a wood frame using four planks of 1x4 (2, 5cm x 10cm) lumber. Pour in concrete to fill in the hole and the frame giving a total of 4" (8-10cm) thick concrete. Be sure surface is level.
12 FRONT 3, 1" 1m (DOOR)
" 3/4 92 4m 2,
Note: Finished Slab dimensions, with lumber removed. Allow 3 - 5 hours for construction and a week for concrete curing time. 9
Anchoring
A10
Anchoring Down The Building
It is important that the entire floor frame be anchored after the building is erected.
Below are recommended ways of anchoring.
Arrow Anchoring Kit: (Model No. AK4 or 60298) Recommended for use with any suggested base. The side floor frames and the rear floor frame are made up of two pieces. The holes in these pieces will align when the pieces are positioned with correct amount of overlap. The illustrations below show the proper overall length for the sides, rear and front. Proceed as follows:
8937
9367 8934
9367
8936
Place the front floor frames as shown. Center the ramp, with drain holes facing outside, on top of the two front floor frames. Join the frames by inserting eight screws.
1
STEP
8934 9367
DRAIN HOLES FACE OUTSIDE
1
Front Floor Frame Assembly 119 3/8" 3, 0m 9367
2 Overlap the side floor frames and
the rear floor frames as shown. The holes in these pieces will align when the pieces are positioned with correct amount of overlap. See the illustrations below for the proper overall length of the side and rear floor frames. Join the frames by inserting four/five bolts into each frame set as shown.
8937 Side Floor Frame 91 1/8" 2, 3m STEP 8937
2
Rear Floor Frame 119 3/8" 3, 0m 8936
8936
3
Double check the length of each and set these pieces aside for later use.
91 1/8" 2, 3m 91 1/8" 2, 3m STEP 119 3/8" 3, 0m Front & Rear 119 3/8" 3, 0m
3
14
Step 2
A15
Parts Needed For
Frame Assemblies
5986 Rear Wall Angle (2) 9917 Rear Wall Channel (2) 9922 Side Wall Channel (4) 8839 Side Wall Angle (4)
The main frame pieces reinforce the walls. These pieces will later be installed in the center and at the top edge of the side walls and the rear wall. Proceed as follows:
9917
Rear Wall Channel 118 1/8" 3, 0m 9917
1
Overlap the rear wall channel pieces as shown in the figure and fasten the two pieces together with one bolt in the center hole (three holes will align).
9922 STEP STEP
Side Wall Channels 89 7/8" 2, 3m 9922
2 Make two side wall channels by
overlapping the side wall channel pieces as shown. Fasten each set together with one bolt in the center hole of each set.
1
5986
2
Rear Wall Angle 118 1/8" 3, 0m 5986
3
Overlap the rear wall angle pieces as shown in the figure and fasten them together with one bolt in the center hole. Make two side wall angles by overlapping the side wall angle pieces as shown. Fasten each set together with one bolt in the center hole.
8839 STEP STEP
Side Wall Angles 89 7/8" 2, 3m 8839
4
3
4
Rear Wall Channel 118 1/8" 3, 0m
Side Wall Channels 89 7/8" 2, 3m
5 Set the assemblies aside. [. . . ] If this does not help, your building may not be level. Shim the corners until holes line up.
Do not fasten at this time
27
Step 15
A28
Parts Needed For
Ridge Caps & Panels
8840 Ridge Cap (1) 7483 Roof Panel (2) 8486 Ridge Cap (1)
1
Install the first ridge cap on the completed roof section using bolts and nuts. Fasten roof panel overlaps not used for ridge cap. Cover the head of bolt with the 2" (5 cm) piece of weather stripping tape. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ARROW VN108-A
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual ARROW VN108-A will begin.