User manual ASK PROXIMA M9

[. . . ] English User's Guide Warning Please read the safety instructions booklet before setting up the projector. · This manual covers only basic operations, including how to set up the projector, and basic projector operations. For more detailed information, see the Reference Guide on the CD-ROM that comes with the projector. Contents Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Using the User Documentation on the CD-ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This projector comes with functions for automatic as well as manual keystone correction, which provides a regularly shaped projected image. Keystone correction can cause the corrected image to be smaller than the original (uncorrected) image, or it can cause distortion of the image. If the projected image becomes difficult to view, try moving the screen and/or projector so they are oriented close to the configuration shown under "Setting Up the Projector" on page 7. The center of the projector's lens should be aligned with the horizontal center of the screen (page 7). Automatic Keystone Correction When "On" is selected for the "Option Settings 1 Auto Keystone Correction" setting of the Setup Menu, the projector will detect the vertical orientation of the object in the image and adjust its shape automatically so it appears as a rectangle. The message "Auto Keystone Corrected. " appears in the lower left corner of the projected image when the projector performs auto keystone correction. The projector's auto keystone correction range is 0 to +30 degrees. If the surface you are projecting onto is angled downwards from horizontal, use manual keystone correction to correct the image. Auto keystone correction is performed by detecting the elevation angle of the projector. This means that the surface you are projecting onto needs to be standing straight up. If the surface you are projecting onto is not straight, use manual keystone correction to correct the image. To use manual keystone correction 1. 3. Press the [KEYSTONE +] or [KEYSTONE ­] key. This causes the keystone correction screen to appear on the projected image. Use the [KEYSTONE +] and [KEYSTONE ­] keys to correct for keystoning. Correction can be performed for keystoning within ±30°. To close the setup screen, press the [ESC] key. 14 Using the Setup Menu Pressing the [MENU] key while an image is being projected displays the setup menu on the projected image. The setup menu can be used to configure a variety of different projector settings. Use the cursor keys to select and configure settings, and the [ENTER] key to register them. Using the Setup Menu The menu items that can be set (or displayed) depend on the current input source. In the following table, the "Input Source" columns indicate whether each item appears ( ) or not ( ) for each input source (R = RGB, C = Component, V = Video, ­ = No input signal). A triangle ( ) indicates that the item can be set (or displayed), subject to certain conditions. Main menu Sub-menu Image Adjustment Brightness Contrast Sharpness Saturation Tint Color Mode Color Balance Vertical Position Horizontal Position Frequency Phase Video Mode Restore Menu Defaults Screen Settings Keystone Correction Aspect Ratio Projection Mode Startup Screen No Signal Screen Blank Screen Restore Menu Defaults Input Settings RGB Input Video Signal Signal Name Indicator Restore Menu Defaults Input Source RCV­ Main menu Sub-menu Option Settings 1 Menu Position Auto Keystone Correction Auto Adjust Eco Mode Auto Power Off Direct Power On Language Restore Menu Defaults Option Settings 2 Zoom Memory Pointer Restore Menu Defaults Operational Info Lamp Time Reset Lamp Time Input Signal Signal Name Index Resolution Horizontal Frequency Vertical Frequency Scan System Restore All Defaults Input Source RCV­ For detailed information about settings and how they are configured, see the Reference Guide on the CD-ROM that comes with the projector. 15 English Troubleshooting Troubleshooting Indicators The status of the indicators lets you know the current operational status of the projector. This section provides details about indicators. "POWER" in the following table stands for the "POWER/STANDBY" indicator. TEMP indicator LAMP indicator POWER/STANDBY indicator Normal Operation Indicators When this indicator: POWER : TEMP : LAMP : POWER : POWER : POWER : POWER : LAMP : Is this: Amber steady Amber steady Amber steady Amber steady Green flashing Green steady Amber flashing Green steady It means this: You have just plugged the AC power cord into a power outlet. Wait until the projector enters the standby state (see below) before trying to turn on power. Standby state: The AC power cord is plugged in and the projector is in standby. Projector is warming up after being turned on. Projector is on and standing by for use. Projector is cooling down after being turned off. If the projector is hot when you plug the AC power cord into a power outlet, it also goes into a cool down state. The projector's Eco Mode is turned on. Error Indicators and Warning Messages When an error occurs, wait until cool down is complete and the fan stops before unplugging the AC power cord. [. . . ] Replace the lamp (see "Replacing the Lamp"). Try performing the following steps, which can return the projector to normal operation. Press the [ ] (power) key to turn off the projector. After the projector's cool down is finished and the fan is completely stopped, unplug the AC power cord. Plug the power cord back in and turn the projector back on again. [. . . ]