User manual ASKO T731

[. . . ] ASKO USE AND CARE GUIDE SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE rom T!e f ing t nc AN RT orma p e r a the PO erf o or IM p ll it f a g st be e a d usin re the , r et r y e r befo g To r d ions u t y o truc e. s tim in t firs DRYER CONTENTS IMPORTANT SAFETY INSTRUCTIONS SAFETY FEATURES ASKO DRYER FEATURES ENERGY SAVING TIPS INSTALLATION INSTRUCTIONS PREPARING THE LAUNDRY T711 OPERATING INSTRUCTIONS T721 OPERATING INSTRUCTIONS T731 OPERATING INSTRUCTIONS T761 AND T781 OPERATING INSTRUCTIONS CARE AND MAINTENANCE INSTRUCTIONS TROUBLESHOOTING PRODUCT WARRANTY INDEX 2 2 3 3 4 10 12 13 14 17 22 24 25 26 Page 1 ENGLISH IMPORT INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS WARNING!To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: Read all instructions before using the appliance. [. . . ] (See "Time" in the "Option Buttons" section below for details. ) BUTT UTTONS OPTION BUTTONS The option buttons allow you to select program time, normal or low temperature, anti-crease, delayed start, buzzer and quick cooling. Each of these options is defined in more detail in the following paragraphs. DELAY This option lets you set the dryer to start at the most convenient time. This feature is also useful in areas where utility companies offer discount rates during offpeak hours. You can set delayed start from 1 hour to 24 hours, in one-hour increments. To set a delayed start time, press the button until the number of hours you wish to delay starting the machine displays on the LED, as illustrated below: TIME SET If you set the program knob to Timed Dry or Air Fluff, you must select the length of drying time by pressing this button until the number of minutes you wish to dry the load displays on the LED. The time advances in 5minute increments and you can select between 5 and 90 minutes. If you pass the time you wanted to select, continue to press the button until the correct time displays. 1h If you pass the time you wanted to select, continue to press the button until the correct time displays. If you decide not to delay starting the unit, continue to press the button until "0" displays. Press Start and the unit will start after the number of hours you selected has passed. To cancel Delay Start after you have pressed the Start button, press and hold the Stop button until the LED displays the program number or, if the program knob is set on 5 or 6, the number of minutes. You can then press Start and the unit will start right then. WRINKLE-FREE The Wrinkle-free option prevents garments from wrinkling if you're unable to remove them right away. You can select one, two, or three hours by pressing the Wrinkle-free button until the number of hours you prefer displays, as illustrated below: 1h NOTE: "0" on the LED indicates the option is not active. When you set a time, the drum will continue to rotate after the program is complete for three seconds every minute until the door is opened or the selected time (1­ 3 hours) has passed. If the buzzer is on, it will sound each time the anti-crease program activates. TEMPERATURE You have two temperature options: Normal and Low. The Normal setting should be used for heavier fabrics, such as denim, cotton, linen, etc. The Low setting should be used for lighter, more delicate fabrics, such as synthetics, permanent press, acrylics, etc. The indicator light will stay lit when Low is selected. It will remain off when Normal is selected. Page 15 ENGLISH Your ASKO dryer has our state-of-the-art Sensidry system. This means it has a humidity sensor that ensures different fabrics always dry thoroughly. This sensor turns off the heat when the laundry has reached the appropriate dryness. activate the humidity sensor. You should be careful when using this option not to overdry the fabrics. [. . . ] After unpacking the dryer, thoroughly check the unit for cosmetic damage. FOR RESIDENTIAL INSTALLATIONS ONLY LENGTH OF WARRANTY Three-Year Full From date of purchase. AM APPLIANCE GROUP WILL PAY FOR: ASKO replacement parts and/or repair labor to correct defect in materials or workmanship. Service must be provided by an authorized ASKO service agent. ASKO replacement parts (labor cost not included) for any defective solid-state controls, timers, motors, or pumps. Service must be provided by an authorized ASKO service agent. [. . . ]