User manual ASL INTERCOM TS 10

[. . . ] It is not necessary to provide rear support by extra bracing or shelving. Adequate ventilation must be provided by allowing sufficient space around the sides and rear of the unit to ensure free circulation of air. The power supply is located on the rear of the unit, and after a period of time it will feel hot to the touch. This is quite normal, and should be no cause for alarm. User Manual TS 120 / Issue 1 2000 ASL Intercom, Utrecht, Holland. 3 4. 0 FRONT PANEL CONTROLS clear 1 2 3 4 5 6 7 8 9 10 11 12 All selected channels 1 ATTENTION button This push button activates the ATTENTION signal for that specific channel. [. . . ] An active preset must be finished (sent ATTN and sent GO) before the next preset maybe selected. - On the active preset activate ATTN by pushing the ATTN button. All programmed channels will go to ATTN mode. - Then push the GO button on the desired moment and all channels will switch from ATTN to GO (red to green). Now you are allowed to switch to the next preset number where you start from pushing the ATTN button again. With the TS-99 unit the presets of the TS-120's can be programmed. - Select the requested preset number on the TS-99 with the "left" and "right" buttons. - Preview the current settings with the "preview" button, all selected channels will be shown in green flashing LED's - To change the setting, press "program". All selected channels will be shown in green flashing LED's, you may change the setting by pushing the GO buttons of the TS-120. After completing your selection of the preset push and hold "Store" until the TS-120 returns to its normal state. User Manual TS 120 / Issue 1 2000 ASL Intercom, Utrecht, Holland. 5 8. 0 CABLING For the THEATER Series system the interconnecting cables are of the shielded two-conductor microphone cable type and the intercom line connectors are of the XLR-3 type. The signals are on XLR pin 3, DC power is on XLR pin 2. XLR pin 1 is connected to the shield of the cable which functions as the common return for audio and power. Since the DC signals are transferred in an unbalanced way, certain rules have to be obeyed when installing the cables of an intercom network. This is to minimize power loss and the possible effects of electromagnetic fields. These rules are: Use high quality (multipair) cable. For interconnecting user stations, power supplies and accessories in an ASL Intercom network, use high quality shielded two-conductor (minimum 2x 0. 30 mm2) microphone cable only. In case of a two channel intercom network, use high quality microphone ' multipair' cable only, each pair consisting of two conductors (minimum 2x 0. 15 mm2) with separate shield. Multipair cable should also have an overall shield. Use flexible single and multipair microphone cable instead of cable with solid cores, especially when the cable is subjected to bending during operation or installation. The screen of each separate microphone cable and/or the screen of each single pair in a multipair cable, should be connected to pin 1 of each XLR-3 connector. Do not connect this cable screen to the metal housing of the connector or to metal wall boxes (outlets). Cable trunks, connection boxes and overall multipair cable screen to clean earth. [. . . ] Avoid using mains outlets which also power dimmer controlled lighting systems. In case of more complex installations, don'hesitate to t contact us. Please send us a block diagram of the planned network with a list of all user stations and their positions, and we are happy to advise you on cabling lay out. 6 User Manual TS 120 / Issue 1 2000 ASL Intercom, Utrecht, Holland. 9. 0 WARRANTY 10. 0 TECHNICAL SPECIFICATIONS TS-120 POWER CONSUMPTION Max LINE DRIVER max. output current output impedance DIMENSIONS AND WEIGHT width height depth weight GENERAL SYSTEM Mains voltage: SPECIFICATIONS 90 - 240 V AC (auto select) 50/60 Hz. [. . . ]