User manual ASROCK 775I915PL-M

[. . . ] 775i915PL-M User Manual Version 1. 0 Published May 2005 Copyright©2005 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] Then connect the white end of SATA power cable to the power connector of the power supply. ASRock 8CH I/O accommodates 4 default USB 2. 0 ports. If those USB 2. 0 ports on the I/O panel are not sufficient, this USB 2. 0 header is available to support 2 additional USB 2. 0 ports. ASRock 8CH I/O accommo- USB 2. 0 Header (9-pin USB67) (see p. 8 No. 19) 1 USB_PWR P-6 P+6 GND DUMMY GND P+7 P-7 USB_PWR USB 2. 0 Header (9-pin USB45) (see p. 8 No. 21) 1 GND P+4 P-4 USB_PWR USB_PWR P-5 P+5 GND DUMMY dates 4 default USB 2. 0 ports. If those USB 2. 0 ports on the I/O panel are not sufficient, this USB 2. 0 header is available to support 2 additional USB 2. 0 ports. This header supports an optional wireless transmitting and receiving infrared module. These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, DVD-ROM, TV tuner card, or MPEG card. This is an interface for front panel audio cable that allows convenient connection and control of audio devices. Infrared Module Header (5-pin IR1) (see p. 8 No. 7) 1 IRTX +5V DUMMY GND IRRX Internal Audio Connectors (4-pin CD1) (CD1: see p. 8 No. 27) CD-R GND GND CD-L CD1 Front Panel Audio Header (9-pin AUDIO1) (see p. 8 No. 23) 1 AUD-OUT-L GND AUD-OUT-R MIC-POWER MIC GND +5VA BACKOUT-R BACKOUT-L 18 System Panel Header (9-pin PANEL1) (see p. 8 No. 18) 1 PLED+ PLEDPWRBTN# GND This header accommodates several system front panel functions. DUMMY RESET# GND HDLEDHDLED+ Chassis Speaker Header (4-pin SPEAKER 1) (see p. 8 No. 13) 1 SPEAKER DUMMY DUMMY +5V Please connect the chassis speaker to this header. Chassis Fan Connector (3-pin CHA_FAN1) (see p. 8 No. 10) GND +12V CHA_FAN_SPEED Please connect a chassis fan cable to this connector and match the black wire to the ground pin. Please connect a CPU fan cable to this connector and match the black wire to the ground pin. Please connect an ATX power supply to this connector. CPU Fan Connector (4-pin CPU_FAN1) (see p. 8 No. 5) GND +12V CPU_FAN_SPEED FAN_SPEED_CONTROL ATX Power Connector (20-pin ATXPWR1) (see p. 8 No. 28) ATX 12V Connector (4-pin ATX12V1) (see p. 8 No. 2) Please connect an ATX 12V power supply to this connector. 19 AT (SAT 2. 10 Serial ATA (SATA) Hard Disks Installation This motherboard adopts Intel ICH6 south bridge chipset that supports Serial ATA (SATA) hard disks. You may install SATA hard disks on this motherboard for internal storage devices. [. . . ] Tolerance ( C) The default value of tolerance is [2], which means the error of the target CPU temperature will be within 2 C. Minimun Fan Speed You can use this option to set the minimun fan speed. The CPU fan speed will be controlled at the rate of 90% or 85%. 3. 5 Boot Screen In this section, it will display the available devices on your system for you to configure the boot settings and the boot priority. Main Advanced BIOS SETUP UTILITY H/W Monitor Boot Security Exit Boot Settings Boot Settings Configuration 1st Boot Device 2nd Boot Device 3rd Boot Device Hard Disk Drives Removable Drives CD/DVD Drives [1st Floppy Device] [HDD: PM - HDS722580VL] [CD / DVD: 3S - CD - ROM C] Configure Settings during System Boot. Enter F1 F9 F10 ESC Select Screen Select Item Go to Sub Screen General Help Load Defaults Save and Exit Exit v02. 54 (C) Copyright 1985-2005, American Megatrends, Inc. 33 3. 5. 1 Boot Settings Configuration BIOS SETUP UTILITY Boot Boot Settings Configuration Boot From Network Bootup Num-Lock [Disabled] [On] To enable or disable the boot from network feature. +F1 F9 F10 ESC Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02. 54 (C) Copyright 1985-2005, American Megatrends, Inc. Boot From Network Use this item to enable or disable the Boot From Network feature. Boot Up Num-Lock If this item is set to [On], it will automatically activate the Numeric Lock function after boot-up. 3. 6 Security Screen In this section, you may set or change the supervisor/user password for the system. [. . . ]