User manual ASROCK 775I915PL-SATA2

[. . . ] 775i915PL-SATA2 User Manual Version 1. 0 Published June 2005 Copyright©2005 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! FDD connector (33-pin FLOPPY1) (see p. 9 No. 23) Pin1 FLOPPY1 the red-striped side to Pin1 Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. Primary IDE connector (Blue) (39-pin IDE1, see p. 9 No. 7) PIN1 IDE1 connect the black end connect the blue end to the IDE devices to the motherboard 80-conductor ATA 66/100 cable Note: Please refer to the instruction of your IDE device vendor for the details. Serial ATA Connectors (SATA1: see p. 9 No. 14) SATA1 SATA2 SATA3 SATA4 Serial ATA II Connector (SATA II_1: see p. 9 No. 10) SATA II_1 These four Serial ATA (SATA) connectors support SATA data cables for internal storage devices. The current SATA interface allows up to 1. 5 Gb/s data transfer rate. This Serial ATA II (SATA II) connector supports SATA II data cables for internal storage devices. The current SATA II interface allows up to 3. 0 Gb/s data transfer rate. It is recommended to plug SATAII HDD to SATAII connector and connect SATAI HDD to SATAI connector. Serial ATA (SATA) Data Cable Either end of the SATA data cable can be connected to the SATA hard disk or the SATA connector on the motherboard. 19 Serial ATA (SATA) Power Cable (Optional) connect to the SATA HDD power connector connect to the power supply Please connect the black end of SATA power cable to the power connector on each drive. Then connect the white end of SATA power cable to the power connector of the power supply. ASRock 8CH I/O accommodates 4 default USB 2. 0 ports. If those USB 2. 0 ports on the I/O panel are not sufficient, this USB 2. 0 header is available to support 2 additional USB 2. 0 ports. ASRock 8CH I/O accommo- USB 2. 0 Header (9-pin USB67) (see p. 9 No. 20) 1 GND P+6 P-6 USB_PWR USB_PWR P-7 P+7 GND DUMMY USB 2. 0 Header (9-pin USB45) (see p. 9 No. 22) 1 GND P+4 P-4 USB_PWR USB_PWR P-5 P+5 GND DUMMY dates 4 default USB 2. 0 ports. If those USB 2. 0 ports on the I/O panel are not sufficient, this USB 2. 0 header is available to support 2 additional USB 2. 0 ports. This header supports an optional wireless transmitting and receiving infrared module. These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, DVD-ROM, TV tuner card, or MPEG card. This is an interface for front panel audio cable that allows convenient connection and control of audio devices. Infrared Module Header (5-pin IR1) (see p. 9 No. 19) 1 IRTX +5VSB DUMMY GND IRRX Internal Audio Connectors (4-pin CD1) (CD1: see p. 9 No. [. . . ] Tolerance ( C) The default value of tolerance is [2], which means the error of the target CPU temperature will be within 2 C. Minimun Fan Speed You can use this option to set the minimun fan speed. The CPU fan speed will be controlled at the rate of 90% or 85%. 3. 5 Boot Screen In this section, it will display the available devices on your system for you to configure the boot settings and the boot priority. Main Advanced BIOS SETUP UTILITY H/W Monitor Boot Security Exit Boot Settings Boot Settings Configuration 1st Boot Device 2nd Boot Device 3rd Boot Device Hard Disk Drives Removable Drives CD/DVD Drives [1st Floppy Device] [HDD: PM - HDS722580VL] [CD / DVD: 3S - CD - ROM C] Configure Settings during System Boot. Enter F1 F9 F10 ESC Select Screen Select Item Go to Sub Screen General Help Load Defaults Save and Exit Exit v02. 54 (C) Copyright 1985-2005, American Megatrends, Inc. 35 3. 5. 1 Boot Settings Configuration BIOS SETUP UTILITY Boot Boot Settings Configuration Boot From Network Bootup Num-Lock [Disabled] [On] To enable or disable the boot from network feature. +F1 F9 F10 ESC Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02. 54 (C) Copyright 1985-2005, American Megatrends, Inc. Boot From Network Use this item to enable or disable the Boot From Network feature. Boot Up Num-Lock If this item is set to [On], it will automatically activate the Numeric Lock function after boot-up. 3. 6 Security Screen In this section, you may set or change the supervisor/user password for the system. [. . . ]