User manual ASROCK ALIVESATA2-GLAN-3212 INSTALLATION GUIDE

[. . . ] No part of this installation guide may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this guide may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Specifications and information contained in this guide are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this guide. [. . . ] After waiting for 15 seconds, use a jumper cap to short 2 pins on CLRCMOS1 for 5 seconds. Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. Note: If you use only one IDE device on this motherboard, please set the IDE device as "Master". please refer to the instruction of your IDE device vendor for the details. Besides, to optimize compatibility and performance, please connect your hard disk drive to the primary IDE connector (IDE1, blue) and CD-ROM to the secondary IDE connector (IDE2, black). These two Serial ATA (SATA) connectors are supported by VIA® VT8237A southbridge, support SATA data cables for internal storage devices. These two Serial ATAII (SATAII) connectors are supported by JMicron® JMB 363 (PCIE x1 interface), support SATA data cables for internal storage devices. Either end of the SATA data cable can be connected to the SATA / SATAII hard disk or the SATA / SATAII connector on the motherboard. Please connect the black end of SATA power cable to the power connector on the drive. Then connect the white end of SATA power cable to the power connector of the power supply. (Optional) connect to the SATA HDD power connector connect to the power supply This connector allows you to receive stereo audio input from sound sources such as a CD-ROM, DVD-ROM, TV tuner card, or MPEG card. This is an interface for the front panel audio cable that allows convenient connection and control of audio devices. Please follow the instruction in our manual and chassis manual to install your system. If you use AC'97 audio panel, please install it to the front panel audio header as below: A. You don't need to connect them for AC'97 audio panel. Enter Advanced Settings, and then select Chipset Configuration. Click the icon on the lower right hand taskbar to enter Realtek HD Audio Manager. Click "Audio I/O", select "Connector Settings" , choose "Disable front panel jack detection", and save the change by clicking "OK". This header accommodates several system front panel functions. Please connect the chassis fan cable to this connector and match the black wire to the ground pin. Please connect the CPU fan cable to this connector and match the black wire to the ground pin. Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin CPU fan still can work successfully even without the fan speed control function. [. . . ] If you want to install Windows® 2000, XP or XP 64-bit on your SATA / SATAII HDDs without RAID functions, please follow below steps. If you plan to install Windows® 2000 / XP / XP 64-bit on VIA® SATA ports without RAID functions, please set the "SATA Operation Mode" option to [non-RAID]. If you plan to install Windows® 2000 / XP / XP 64-bit on JMicron® SATAII ports without RAID functions, please set the "PCIE-SATAII Operation Mode" option to [IDE] or [AHCI]. ) If you set "PCIE-SATAII Operation Mode" to [AHCI] mode, and plan to install Windows® 2000 / XP / XP 64-bit on JMicron® SATAII HDDs, please refer to step 2 on page 21 for detailed procedures of making a SATAII driver diskette. [. . . ]