User manual ASROCK IMB-147 SERIES

[. . . ] IMB-147 User Manual Version 1. 0 Published January 2013 Copyright©2013 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] 27) 1 SPK_RSPK_R+ SPK_LSPK_L+ 20 VGA Header (10-pin VGA_H1) (see p. 10, No. 28) 1 2 PIN Signal Name PIN Signal Name 9 7 5 3 1 RED GRN BLUE HSYNC DDC_CLK 10 8 6 4 2 GND GND GND VSYNC DDC_DAT 21 2. 7 Jumpers Setup The illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when a jumper cap is placed on these 2 pins. Clear CMOS Jumper (3-pin CLRCMOS1) (see p. 10, No. 18) Default Clear CMOS CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, user default profile, 1394 GUID and MAC address will be cleared only if the CMOS battery is removed. COM Port Power Setting Jumpers (3-pin COM4) (see p. 10, No. 17) 1-2 : +5V 2-3 : +12V 22 Panel Power Jumper (3-pin PNL_PWR1) (see p. 10, No. 3) 1-2 : +3V 2-3 : +5V ATX/AT Mode Jumper (3-pin PWR_JP1) (see p. 10, No. 13) 1-2 : AT Mode 2-3 : ATX Mode 23 2. 8 Operating System Setup This motherboard supports Microsoft® Windows® 7. Because motherboard settings and hardware options vary, use the setup procedures in this chapter for general reference only. Refer your OS documentation for more information. 2. 8. 1 Installing Windows® 7 without RAID Using AHCI Mode STEP 1: Set Up UEFI. Press <F2> or <Delete> at system POST. Set AHCI Mode in UEFI Setup Utility > Advanced > Storage Configuration > SATA Mode. STEP 2: Install Windows® 7 on your system. Using IDE Mode STEP 1: Set Up UEFI. Press <F2> or <Delete> at system POST. [. . . ] PCI Devices Power On Use this item to enable or disable PCI devices to turn on the system from the power-soft-off mode. Ring-In Power On Use this to enable or disable the Ring-In signals to turn on the system from power-soft-off mode. RTC Alarm Power On Use this to enable or disable the RTC (Real Time Clock) to power on the system. USB Keyboard/Remote Power On Use this to enable or disable the USB Keyboard/Remote to power on the system. [. . . ]