User manual ASROCK K8 COMBO-Z

[. . . ] MOTHERBOARD K8 Combo-Z User Manual Version 1. 0 Published July 2004 Copyright©2004 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] Then connect the white end of SATA power cable to the power connector of the power supply. ASRock 8CH I/O provides you 4 ready-to-use USB 2. 0 ports on the rear panel. If the rear USB ports are not sufficient, this USB 2. 0 header is available to support 2 extra USB 2. 0 ports. ASRock 8CH I/OTM provides you 4 ready-to-use USB 2. 0 ports on the rear panel. If the rear USB ports are not sufficient, this USB 2. 0 header is available to support 2 extra USB 2. 0 ports. This header supports an optional wireless transmitting and receiving infrared module. This connector allows you to receive stereo audio input from sound sources such as a CDROM, DVD-ROM, TV tuner card, or MPEG card. This is an interface for the front panel audio cable that allows convenient connection and control of audio devices. USB 2. 0 Header (9-pin USB67) (see p. 9, No. 19) 1 USB_PWR P-6 P+6 GND DUMMY GND P+7 P-7 USB_PWR USB 2. 0 Header (9-pin USB_H45) (see p. 9, No. 20) 1 USB_PWR P-5 P+5 GND DUMMY GND P+4 P-4 USB_PWR Infrared Module Header (5-pin IR1) (see p. 9, No. 30) 1 IRTX +5V DUMMY GND IRRX Internal Audio Connector (4-pin CD1) (see p. 9, No. 26) CD-R GND GND CD-L Front Panel Audio Header (9-pin AUDIO1) (see p. 9, No. 28) 1 GND +5VA BACKOUT-R BACKOUT-L AUD-OUT-L GND AUD-OUT-R MIC-POWER MIC Bridge Fan Connector (3-pin NB_FAN1) (see p. 9, No. 16) GND +12V CHA_FAN_SPEED Please connect the Bridge fan cable to this connector and match the black wire to the ground pin. 19 System Panel Header (9-pin PANEL1) (see p. 9, No. 17) 1 PLED+ PLEDPWRBTN# GND This header accommodates several system front panel functions. DUMMY RESET# GND HDLEDHDLED+ Chassis Speaker Header (4-pin SPEAKER 1) (see p. 9, No. 18) 1 SPEAKER DUMMY DUMMY +5V Please connect the chassis speaker to this header. Chassis Fan Connector (3-pin CHA_FAN1) (see p. 9, No. 15) GND +12V CHA_FAN_SPEED Please connect the chassis fan cable to this connector and match the black wire to the ground pin. Please connect the CPU fan cable to this connector and match the black wire to the ground pin. Connect a Game cable to this connector if the Game port bracket is installed. CPU Fan Connector (3-pin CPU_FAN1) (see p. 9, No. 9) CPU_FAN_SPEED +12V GND Game Connector (15-pin GAME1) (see p. 9, No. 25) 1 +5V JBB1 JBX MIDI_OUT JBY JBB2 MIDI_IN +5V JAB2 JAY GND GND JAX JAB1 +5V ATX Power Connector (20-pin ATXPWR1) (see p. 9, No. 2) Please connect an ATX power supply to this connector. ATX 12V Connector (4-pin ATX12V1) (see p. 9, No. [. . . ] For the user password, you may also clear it. BIOS SETUP UTILITY H/W Monitor Boot Main Advanced Security Exit Security Settings Supervisor Password User Password : Not Installed : Not Installed Install or Change the password. Change Supervisor Password Change User Password Clear User Password Enter F1 F9 F10 ESC Select Screen Select Item Change General Help Load Defaults Save and Exit Exit v02. 54 (C) Copyright 1985-2003, American Megatrends, Inc. 36 3. 7 Exit Screen Main Advanced BIOS SETUP UTILITY H/W Monitro Boot Security Exit system setup after saving the changes. F10 key can be used for this operation. Exit Exit Options Save Changes and Exit Discard Changes and Exit Discard Changes Load Optimal Defaults Enter F1 F9 F10 ESC Select Screen Select Item Go to Sub Screen General Help Load Defaults Save and Exit Exit v02. 54 (C) Copyright 1985-2003, American Megatrends, Inc. Save Changes and Exit When you select this option, it will pop-out the following message, "Save configuration changes and exit setup?" Select [OK] to save the changes and exit the BIOS SETUP UTILITY. Discard Changes and Exit When you select this option, it will pop-out the following message, "Discard changes and exit setup?" Select [OK] to exit the BIOS SETUP UTILITY without saving any changes. Discard Changes When you select this option, it will pop-out the following message, "Discard changes?" Select [OK] to discard all changes. [. . . ]