User manual ASROCK M266A R3.0

[. . . ] M266A User Manual Version 3. 0 Published July 2003 Copyright©2003 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] Because the BIOS software is constantly being updated, the following BIOS setup screens and descriptions are for refer ence purpose only, and may not exactly match what you see on your screen. 3. 2 BIOS Setup Utility Main Menu When you enter the BIOS Setup utility, the following screen appears: AMIBIOS SETUP UTILITY - VERSION 3. 31a M266 (A) BIOS P1. 50 Standard CMOS Setup Advanced CMOS Setup Advanced Chipset Setup Power Management Setup PCI / Plug and Play Setup Peripheral Setup Hardware Monitor Setup Change Supervisor Password Change User Password Auto Configuration with Optimal Settings Save Savings and Exit Exit Without Saving F1: Help Esc: Exit : Select Item : Select Menu +/-: Change Values Enter: Select Sub-Menu F9: Setup Defaults F10: Save & Exit Set Time, Date, Hard Disk Type . . The main menu of the Setup Utility displays a list of the options that are available. The highlighted item is currently selected. Use arrow keys to move the highlight bar to select items, then press <Enter> to make configuration for a specific item. 15 3. 3 Legend Bar At the bottom of all the Setup Screen is a legend bar. The following table lists the keys in the legend bar with their corresponding functions: Navigation Key(s) <F1> <ESC> / / +/<Enter> <F9> <F10> Function Description Displays the General Help Screen Jumps to the Exit menu or returns to the upper menu from the current menu Moves cursor up or down between fields Selects menu to the left or right Increases or decreases values Brings up a selected menu for a highlighted field Loads all the setup items to the default value Saves changes and exits Setup 3. 4 Standard CMOS Setup This menu lists out the basic information about your system. AMIBIOS SETUP UTILITY - VERSION 3. 31a Standard CMOS Setup System Date System Time Floppy Drives IDE Devices BIOS Version Processor Type Processor Speed Cache Size Microcode Update Total Memory DDR1 DDR2 [ Setup Help ] Jul 08 2003 Tue 20:07:40 Month: Jan - Dec Day: 01 - 31 Year: 1980 - 2099 M266<A> BIOS P1. 50 Pentium (R) 4 CPU 2400 MHz 512 KB F24 / 0F 224 MB + 32 MB Share Memory 256 MB / 100 MHz <DDR 200> None F1:Help Esc:Previous Menu :Select Item +/-:Change Values Enter:Select Sub-Menu F9:Setup Defaults F10:Save & Exit System Date [Month/Day/Year] Set the system date that you specify. Valid values for month, day, and year are Month: [Jan to Dec], Day: [1 to 31], Year: [1980 to 2099). Use keys to move between the Month, Day and Year fields. System Time [Hour:Minute:Second] Set the system to the time that you specify. Use keys to move between the Hour, Minute and Second fields. Floppy Drives Use this to set the type of floppy drives installed. 16 IDE Devices Use this to configure IDE devices. There are two IDE channels (Primary and Secondary) available in your system, and each channel can be installed with one or two devices (Master and Slave). Use these items to configure each device on the IDE channel. Highlight "Primary IDE Master" then press <Enter> to display the submenu: AMIBIOS SETUP UTILITY - VERSION 3. 31a Primary IDE Master: [ Setup Help ] Select how to set the parameters of drive, Or Select [AUTO] to set all HDD parameters automatically. On On Auto On Auto Type Cylinders Heads Write Precompensation Sectors Maximum Capacity LBA Mode Block Mode Fast Programmed I/O Modes 32 Bit Transfer Mode Ultra DMA Mode Auto F1:Help Esc:Previous Menu :Select Item +/-:Change Values Enter:Select Sub-Menu F9:Setup Defaults F10:Save & Exit TYPE It allows user to select the type of the IDE Drive. After making your selections on this sub-menu, press <ESC> key to return to the upper menu, in whcih the hard disk drive field will display the size for the hard disk drive that you configured. [USER]: It allows user to manually enter the number of cylinders, heads, and sectors per track for the drive. Before attempting to configure a hard disk drive, make sure you have the correct configuration information supplied by the drive manufacturer. Incorrect settings may cause the system to fail to recognize the installed hard disk. [Auto]: Select [Auto] to automatically detect hard disk drive. If autodetection is successful, the BIOS Setup automatically fills in the correct values for the remaining fields on this sub-menu. If the auto-detection fails, it may due to that the hard disk is too old or too new. If the hard disk was already formatted on an older system, the BIOS Setup may detect incorrect parameters. [. . . ] Parallel Port Mode Set the operation mode of the parallel port. If this option is set to [ECP+EPP], it will show the EPP version in the following item, "EPP Version". OnBoard Midi Port Select address for Midi Port or disable Midi Port. Configuration options: [Disabled], [330], [300], [290], [292]. [. . . ]