User manual ASROCK P4I45E R3.0

[. . . ] P4i45E User Manual Version 3. 0 Published October 2003 Copyright©2003 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] If the rear USB ports are not sufficient, this header is available to support 2 additional USB 2. 0 ports. This connector supports an optional wireless transmitting and receiving infrared module. Infrared module connector (5-pin IR1) (see p. 9 item 17) 1 IRTX +5V DUMMY GND IRRX 16 Internal audio connectors (4-pin CD1, 4-pin AUX1) (CD1: see p. 9 item 26) (AUX1: see p. 9 item 25) AUX-L GND GND AUX-R CD-L GND GND CD-R AUX1 These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, DVD-ROM, TV tuner card, or MPEG card. This is an interface for front panel audio cable that allows convenient connection and control of audio devices. CD1 Front panel audio connector (9-pin AUDIO1) (see p. 9 item 24) 1 GND +5VA BACKOUT-R BACKOUT-L AUD-OUT-L GND AUD-OUT-R MIC-POWER MIC System panel connector (9-pin PANEL1) (see p. 9 item 13) 1 PLED+ PLEDPWRBTN# GND This connector accommodates several system front panel functions. DUMMY RESET# GND HDLEDHDLED+ Chassis speaker connector (4-pin SPEAKER 1) (see p. 9 item 14) 1 SPEAKER DUMMY DUMMY +5V This connector allows you to attach to an external speaker. Chassis fan connector (3-pin CHA_FAN1) (see p. 9 item 15) CPU_FAN_SPEED +12V GND Connect the fan cable to the connector matching the black wire to the ground pin. Connect the fan cable to the connector matching the black wire to the ground pin. Connect an ATX power supply to the connector. CPU fan connector (3-pin CPU_FAN1) (see p. 9 item 27) GND +12V CHA_FAN_SPEED ATX power connector (20-pin ATXPWR1) (see p. 9 item 6) 17 Chapter 3 BIOS Setup 3. 1 BIOS Setup Utility This section explains how to configure your system using the BIOS Setup Utility. The BIOS FWH chip on the motherboard stores the BIOS Setup Utility. When you start up the computer, there is a chance for you to run the BIOS Setup. Press <F2> during the Power-On-Self-Test (POST) to enter the BIOS Setup Utility, otherwise, POST continues with its test routines. If you wish to enter the BIOS Setup after POST, restart the system by pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system chassis. You can also restart by turning the system off and then back on. The BIOS Setup Utility is designed to be user-friendly. It is a menu-driven program, which allows you to scroll through its various sub-menus and select among the predetermined choices. Because the BIOS software is constantly being updated, the following BIOS setup screens and descriptions are for reference purpose only, and may not exactly match what you see on your screen. 3. 1. 1 BIOS Menu Bar The top of the screen has a menu bar with the following selections: MAIN Sets up the basic system configuration ADVANCED Sets up the advanced features SECURITY Sets up the security features POWER Configures Power Management features BOOT Configures the default system device that is used to locate and load the Operating System EXIT Exits the current menu or the BIOS Setup To access the menu bar items, press the right or left arrow key on the keyboard until the desired item is highlighted. 3. 1. 2 Legend Bar At the bottom of the Setup Screen is a legend bar. The following table lists the keys in the legend bar with their corresponding functions. 18 Navigation Key(s) <F1> <ESC> / / +/<Enter> <F9> <F10> Function Description Displays the General Help Screen Jumps to the Exit menu or returns to the upper menu from the current menu Moves cursor up or down between fields Selects menu to the left or right Increases or decreases values Brings up a selected menu for a highlighted field Loads all the setup items to the default values Saves changes and exits Setup 3. 2 Main Menu When you enter the BIOS Setup Utility, the following screen appears. Main Advanced Security AMIBIOS SETUP UTILITY - VERSION 3. 31a Boot Power Exit [ Setup Help ] System Date System Time Floppy Drives IDE Devices BIOS Version Processor Type Processor Speed Cache Size Microcode Update Total Memory DDR1 DDR2 Oct 27 2003 Mon 16:07:40 Month: Jan - Dec Day: 01 - 31 Year: 1980 - 2099 P4I45E BIOS P2. 10 Pentium (R) 4 CPU 2400 MHz 512 KB F24 / 18 256 MB 256 MB / 133 MHz (DDR266) None F1:Help Esc:Exit :Select Item :Select Menu +/-:Change Values Enter:Select Sub-Menu F9:Setup Defaults F10:Save & Exit System Date [Month/Day/Year] Set the system date that you specify. Valid values for month, day, and year are Month: (Jan to Dec), Day: (1 to 31), Year: (up to 2099). Use keys to move between the Month, Day and Year fields. System Time [Hour:Minute:Second] Set the system to the time that you specify. Use keys to move between the Hour, Minute and Second fields. Floppy Drives Use this to set the type of floppy drives installed. IDE Devices Use this to configure IDE devices. 19 TYPE To set the type of the IDE device, first, please select "IDE Devices" on Main menu and press <Enter> to get into the sub-menu. Then, select among "Primary IDE Master", "Primary IDE Slave", "Secondary IDE Master", and "Secondary IDE Slave" to make configuration of its type. After making your selections on this sub-menu, press <ESC> key to return to the upper menu, in whcih the hard disk drive field will display the size of the hard disk drive that you configured. [. . . ] Repost Video on S3 Resume: This feature allows you to repost video on S3 resume. It is recommended to enable this feature under Microsoft® Windows® 98 / ME. Restore on AC/Power Loss: This allows you to set the power state after an unexpected AC/power loss. If [Power Off] is selected, the AC/power remains off when the power recovers. [. . . ]