User manual ASROCK P4I45GV R5.0

[. . . ] P4i45GL P4i45GV User Manual Version 5. 1a Published February 2004 Copyright©2004 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! Connector FDD Connector (33-pin FLOPPY1) (see p. 10/p. 11, No. 13) Figure Description Pin1 FLOPPY1 the red-striped side to Pin1 Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. Primary IDE Connector (Blue) (39-pin IDE1, see p. 10/p. 11, No. 9) Secondary IDE Connector (Black) (39-pin IDE2, see p. 10/p. 11, No. 8) PIN1 IDE1 PIN1 IDE2 connect the blue end to the motherboard 80-conductor ATA 66/100 cable connect the black end to the IDE devices Note: If you use only one IDE device on this motherboard, please set the IDE device as "Master". Please refer to the instruction of your IDE device vendor for the details. Besides, to optimize compatibility and performance, please connect your hard disk drive to the primary IDE connector (IDE1, blue) and CD-ROM to the secondary IDE connector (IDE2, black). USB 2. 0 Header (9-pin USB45) (see p. 10/p. 11, No. 19) 1 GND P+4 P-4 USB_PWR USB_PWR P-5 P+5 GND DUMMY ASRock I/OTM accommodates 4 default USB 2. 0 ports. If those USB 2. 0 ports on the I/O panel are not sufficient, this USB 2. 0 header is available to support 2 additional USB 2. 0 ports. This header supports an optional wireless transmitting and receiving infrared module. Infrared Module Header (5-pin IR1) (see p. 10/p. 11, No. 16) 1 IRTX +5V DUMMY GND IRRX 18 Internal Audio Connectors (4-pin CD1, 4-pin AUX1) (CD1: see p. 10/p. 11, No. 26) CD-R GND GND CD-L CD1 These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, DVD/ROM, TV tuner card, or MPEG card. This is an interface for front panel audio cable that allows convenient connection and control of audio devices. AUX-R GND GND AUX-L AUX1 Front Panel Audio Header (9-pin AUDIO1) (see p. 10/p. 11, No. 25) 1 GND +5VA BACKOUT-R BACKOUT-L AUD-OUT-L DUMMY AUD-OUT-R MIC-POWER MIC System Panel Header (9-pin PANEL1) (see p. 10/p. 11, No. 14) 1 PLED+ PLEDPWRBTN# GND This header accommodates several system front panel functions. DUMMY RESET# GND HDLEDHDLED+ Chassis Speaker Header (4-pin SPEAKER 1) (see p. 10/p. 11, No. 15) 1 SPEAKER DUMMY DUMMY +5V Please connect the chassis speaker to this header. Chassis Fan Connector (3-pin CHA_FAN1) (see p. 10/p. 11, No. 12) GND +12V CHA_FAN_SPEED Please connect the chassis fan cable to this connector and match the black wire to the ground pin. Please connect the CPU fan cable to this connector and match the black wire to the ground pin. Please connect the ATX power supply to this header. CPU Fan Connector (3-pin CPU_FAN1) (see p. 10/p. 11, No. 5) GND +12V CPU_FAN_SPEED ATX Power Header (20-pin ATXPWR1) (see p. 10/p. 11, No. 2) COM Port Header (9-pin COM1) (see p. 10/p. 11, No. [. . . ] Select [Auto] will enable this feature if the system supports it. Repost Video on STR Resume: This feature allows you to repost video on STR resume. It is recommended to enable this feature under Microsoft® Windows® 98 / ME. Restore on AC/Power Loss: This allows you to set the power state after an unexpected AC/power loss. [. . . ]