User manual ASROCK P4TWINS-HDTV

[. . . ] P4Twins-HDTV User Manual Version 1. 1 Published November 2005 Copyright©2005 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] Connect the Male/Male RCA patch cables to the Typical HDTV component Video Input connectors and the RCA-type component video connectors (Y-CON1, PB-CON1, and PR-CON1) (Y-CON1, see page 19, No. Turn on your computer and wait system to boot into OS. Click the Settings tab and then the Advanced button. Click the TV button. 21 D. Click the enable button or disable button accordingly for YPbPr display output. Enable Button (Green) Disable Button (Red) Click OK or Apply to save the changes or use hot key to do fast switching between CRT and YPbPr. (Please refer to Step 3 on page 20 for details. ) E. 2. 7. 2 TV Support Function Connecting to TV With AV Output Capability Step 1. Connect the AV video cable to the Typical TV Video Input connector (yellow) and the RCA-type component video connector (blue) / AV (composite) signal connector (PB-CON1, see page 19, No. Turn on your computer and wait system to boot into OS. Connecting to VGA Monitor and TV With AV Output Capability When you install both VGA monitor cable and AV video cable to VGA_HDTV panel at the same time, the default enabled screen is the VGA monitor. You are able to switch the monitor display to TV display by following the below instruction. Connect one end of the VGA monitor cable to your monitor, and the other end to the VGA port (VGA1, see page 19, No. Connect the AV video cable to the Typical TV Video Input connector (yellow) and the RCA-type component video connector (blue) / AV (composite) signal connector (PB-CON1, see page 19, No. Turn on your computer and wait system to boot into OS. Switch the monitor display to TV display and select proper TV format. For selecting proper TV format, please follow the below steps: A. Click the Windows Start button, point at Settings, and then click Control Panel. Double-click the Display icon, click the Settings tab, and use the Screen Area slider to select the resolution you want. Click the Advanced button, then click the Displays tab. Your TV will start to display. 22 2. 8 Technology Untied Overclocking Technology tton (Red) This motherboard supports Untied Overclocing Technology, which means during overclocking, FSB enjoys better margin due to fixed PCI / PCIE buses. Before you enable Untied Overclocking function, please enter "Overclock Mode" option of BIOS setup to set the selection from [Auto] to [CPU, PCIE, Async. ]. Therefore, CPU FSB is untied during overclocking, but PCI and PCIE buses are in the fixed mode so that FSB can operate under a more stable overclocking environment. 2. 9 AT (SAT Serial ATA (SATA) Hard Disks Installation This motherboard adopts ULi M1573 southbridge chipset that supports Serial ATA (SATA) hard disks and RAID functions (RAID 0, 1, JBOD). You may install SATA hard disks on this motherboard for internal storage devices. This section will guide you to install the SATA hard disks. STEP 1: Install the SATA hard disks into the drive bays of your chassis. [. . . ] Configuration options: [IRQ5] and [IRQ7]. OnBoard Game Port Use this item to enable the Game Port or disable it. OnBoard MIDI Port Use this itme to select the address for the MIDI Port or disable it. Configuration options: [Disabled], [300], and [330]. 36 3. 3. 8 USB Configuration BIOS SETUP UTILITY Advanced USB Configuration USB Controller USB 2. 0 Support Legacy USB Support [Enabled] [Enabled] [Disabled] To enable or disable the onboard USB controllers. +F1 F9 F10 ESC Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02. 54 (C) Copyright 1985-2005, American Megatrends, Inc. USB Controller Use this item to enable or disable the use of USB controller. [. . . ]