User manual ASUS ADD2 HDMI DVI CARD INSTALLATION

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Contents Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] ATX power connectors (24-pin EATXPWR, 4-pin ATX12V) These connectors are for an ATX power supply. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. · We recommend that you use an ATX 12 V Specification 2. 0-compliant power supply unit (PSU) with a minimum of 300 W power rating. This PSU type has 24-pin and 4-pin power plugs. If you intend to use a PSU with 20-pin and 4-pin power plugs, make sure that the 20-pin power plug can provide at least 15 A on +12 V and that the PSU has a minimum power rating of 300 W. The system may become unstable or may not boot up if the power is inadequate. Do not forget to connect the 4-pin ATX +12 V power plug; otherwise, the system will not boot up. We recommend that you use a PSU with higher power output when configuring a system with more power-consuming devices. The system may become unstable or may not boot up if the power is inadequate. You must install a PSU with a higher power rating if you intend to install additional devices. · · · · EATXPWR +3 Volts -12 Volts Ground PSON# ATX12V Ground Ground GND GND Ground +12V DC +12V DC -5 Volts +5 Volts +5 Volts +5 Volts connectors Ground +3 Volts +3 Volts Ground +5 Volts Ground +5 Volts Ground Power OK +5V Standby +12 Volts +12 Volts +3 Volts ADD2 HDMI DVI ® ADD2 HDMI DVI ATX power ASUS ADD2 HDMI DVI 1-33 1 3 . System panel connector (20-1 pin PANEL) This connector supports several chassis-mounted functions. PWR LED SPKR +5V Ground Ground Speaker PLED+ PLED- PANEL IDE_LED+ IDE_LEDADD2 HDMI DVI ® HD_LED RESET PWR BTN ADD2 HDMI DVI System panel connector * Requires an ATX power supply. · System power LED This 3-pin connector is for the system power LED. Click N e x t t. ASUS ADD2 HDMI DVI 2-3 4. From the FTP site, select the BIOS version that you wish to download. Follow the screen instructions to complete the update process. The ASUS Update utility is capable of updating itself through the Internet. Always update the utility to avail all its features. 5. Updating the BIOS through a BIOS file To update the BIOS through a BIOS file: 1. Launch the ASUS Update utility from the Windows® desktop by clicking S t a r t > P r o g r a m s > A S U S > A S U S U p d a t e > e. A S U S U p d a t e The ASUS Update main window appears. Select U p d a t e B I O S f r o m a f i l e option from the drop-down menu, then click N e x t t. 2. 3. O p e n window, then click O p e n Follow the screen instructions to complete the update process. 2-4 Chapter 2: BIOS setup 2. 1. 2 1. Creating a bootable floppy disk Do either one of the following to create a bootable floppy disk. DOS environment a. Insert a 1. 44MB floppy disk into the drive. At the DOS prompt, type format A:/S then press <Enter>. Windows® XP environment a. Insert a 1. 44 MB floppy disk to the floppy disk drive. Click S t a r t from the Windows® desktop, then select M y r. [. . . ] Select E x i t & S a v e C h a n g e s or make other changes before saving the values to the non-volatile RAM. Discard Changes This option allows you to discard the selections you made and restore the previously saved values. After selecting this option, a confirmation appears. Select Y E S to discard any changes and load the previously saved values. 2-42 Chapter 2: BIOS setup This chapter describes the contents of the support CD that comes with the motherboard package. Software support 3 3. 1 Installing an operating system This motherboard supports Windows® 2000/XP operating systems (OS). Always install the latest OS version and corresponding updates to maximize the features of your hardware. · Motherboard settings and hardware options vary. [. . . ]