User manual ASUS AP130-E1

[. . . ] AP130-E1 Intel® Pentium® 4 5U Rackmount Server 800/533MHz Front Side Bus User Guide E1548 First Edition V1 April 2004 Copyright © 2004 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ASUS provides this manual "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASUS, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of use or data, interruption of business and the like), even if ASUS has been advised of the possibility of such damages arising from any defect or error in this manual or product. [. . . ] Unhook the hinge-like tabs from the holes on the right side of the front panel to completely detach the front panel assembly from the chassis. Do not use too much force when removing the front panel assembly. Hinge-like tab 2-12 Chapter 2: Hardware setup 2. 5. 2 Re-installing the front panel assembly To re-install the front panel assembly (front bezel and front panel cover): 1. Insert the four hinge-like tabs to the holes on the right edge of the chassis. Swing the front panel to the left and fit the four (4) hooked tabs to the left side of the chassis until the tabs snap back in place. 1 Hinge-like tab 2 Hooked tab ASUS AP130-E1 barebone server 2-13 2. 6 5. 25-inch drives If you have previously used and powered up the system, and that it may be connected to an AC power source, make sure to unplug the power cable before installing or removing any system components. Failure to do so may cause damage to the motherboard and other system components! Three 5. 25-inch drive bays are located on the upper front part of the chassis. A CD-ROM drive that comes standard with the system package occupies the uppermost bay (labeled 1). The two lower bays (labeled 2 and 3) are available for additional 5. 25-inch devices. 1 2 3 To install a 5. 25-inch drive: 1. Use a Phillips (cross) screwdriver to remove the screws that secure the metal cover of the bay where you wish to install the drive. 2. From the side of the drive bay, slide the drive bay lock by pushing it to the left to release the drive lock bar. Drive lock bar Drive bay lock 2-14 Chapter 2: Hardware setup 3. When released, pull up the drive bay lock bar. Underneath the lock bar are two pegs that match the holes on the drive bay. This mechanism secures the drive to the bay in place of screws. Lock pegs Drive bay holes 4. While holding up the drive lock bar, carefully insert a 5. 25-inch drive into the bay, until the back of the drive aligns to the rear edge of the drive cage. Due to space constraints inside the chassis, do not insert the drive all the way at this time. This will allow you enough space to easily connect the drive cables. 5. Connect the IDE cable to the IDE connector on the back of the drive. Connect a 4-pin plug from the power supply to the power connector on the back of the drive. IDE cable Power plug ASUS AP130-E1 barebone server 2-15 7. Make sure that the drive and bay holes align as shown. When in place, the drive protrudes about an inch from the front panel. 8. Pull down the bar lock and insert the lock pegs to the drive/bay holes, then push the drive lock to the right to secure the drive. 9. On the front panel assembly, detach the plastic bay cover opposite the 5. 25-inch drive that you installed by pressing the two hooked tabs on each side of the bay cover. 10. Re-install the front panel assembly when done. Refer to section "2. 5. 2 Re-installing the front panel assembly" for instructions. 2-16 Chapter 2: Hardware setup 2. 7 Hard disk drives 2. 7. 1 Installing a hot-swap SATA hard disk drive To install a SATA HDD: 1. Open the front bezel to access the hot-swap drive trays. [. . . ] Position the I/O board into the bay with the component side to the left (close to the HDDs). Connect the I/O cables to the connectors on the back of the I/O board. USB 2. 0 connector 3. Insert the I/O board into the bay until the bracket fits the front edge of the bay. Secure the I/O board bracket with a screw. 2-42 Chapter 2: Hardware setup 2. 10. 7 Chassis footpads and roller wheels The barebone server system is shipped with four footpads attached to the bottom of the chassis for stability. [. . . ]