User manual ASUS AP140R

[. . . ] ® AP140R Pentium 4 1U Rackmount Server ® User's Manual Disclaimer/Copyrights No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. [. . . ] To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. When adding or removing any additional devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device. If the power supply is broken, do not try to fix it by yourself. Contact an authorized dealer. · · · CAUTION This product is equipped with a three-wire power cable and plug for the user's safety. Use the power cable with a properly grounded electrical outlet to avoid electrical shock. Operation Safety IMPORTANT · · · Any mechanical operation on this server must be conducted by certified or experienced engineers. Before operating the server, carefully read all the manuals included with the server package. Before using the server, make sure all cables are correctly connected and the power cables are not damaged. If any damage is detected, contact your dealer as soon as possible. To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry. Avoid dust, humidity, and temperature extremes. Place the server on a stable surface. · · 8 Introduction "About This Manual" introduces the contents of this document. This part includes the target audience, chapter description, and conventions used. It also lists other sources of information that are not contained in this manual. AP140R Server User's Manual About This Manual 9 Audience This installation guide is intended for system integrators, and experienced users with at least a basic knowledge on configuring an entry-level server. Contents This manual contains the following parts: Introduction: About This Manual This part introduces the contents of this document. Read all documentation before assembling or modifying the server. AP140R Server User's Manual 11 System Package Contents The following checklist enumerates the components included in the standard system package. ASUS AR-10 1U Rackmount Chassis · 200W ATX Power Supply · Slim-type CD-ROM Drive · 1. 44MB Slim-type Floppy Disk Drive · Front Bezel · CPU Heatsink (without fan) · AC Power Cord · This System User's Manual ASUS NB-LM Motherboard · 32-bit/33MHz PCI Riser Card · Support CD with Drivers and Utilities · Motherboard User's Manual Slide Rail Assembly (Rail Kit) · Server-side and rack-side rails · Mounting Ears Assembly · Rail Kit User's Manual ASUS System Management Software CD · System Management Software User's Manual If any of the above items is missing, contact your dealer. 12 Introduction: About This Manual Chapter 1 AP140R Server User's Manual System Overview 13 This chapter describes the general features of the server. This includes sections on front panel, rear panel, and internal features of the server. 1. 1 System Features The ASUS AP140R Server is a 1U rackmount form factor that accommodates the ASUS NB-LM motherboard. The server is powered by Intel® Pentium® 4 processor, and supports the latest I/O and video technologies through the chipsets embedded on the motherboard. Following are highlights of the server's many features. · · Processor: Support for one 478-pin Intel® Pentium® 4 Northwood processor up to 3GHz. Memory: Three DIMM sockets that support Intel PC133/PC100compliant DIMMs, NEC's VC133-compliant Virtual Channel (VC) SDRAM, or Enhanced Memory System's High-speed DRAMs (HSDRAMs) up to 3GB System Chipset: Intel® 845 (Brookdale) chipset. The MCH and the South bridge Intel I/O Controller Hub 2 (ICH2) are interconnected through the Intel proprietary Hub interface. [. . . ] Secure the drive cage to the chassis with two screws in the areas indicated by circles. Connect the floppy dirve cable to the connector on the rear of the drive. Slim Floppy Disk Drive Cable 32 Chapter 4: Hardware Options 3. 3 Cooling System CPU Blower The system has one 9 cm CPU blower that maintains the optimal CPU temperature. The blower is secured to the bracket using two screws from the bottom side. CPU Blower IMPORTANT Make sure that the 3-pin blower cable is connected to the connector marked CPU_FAN on the motherboard to prevent thermal monitoring problems. AP140R Server User's Manual 33 3. 3 Cooling System Chassis Fans Also included in the server cooling system are chassis fans that help maintain efficient air circulation among the components within the chassis. The chassis fans are attached to the metal bracket between the disk drives and the motherboard components. CPU Blower Chassis Fan 1 Chassis Fan 2 Rear View Front View IMPORTANT Make sure that the chassis fan cables are connected to the chassis fan connectors on the motherboard to prevent thermal monitoring problems. 34 Chapter 4: Hardware Options 3. 4 Cable Connections Most of the cables in the server are already pre-connected to their respective connectors. [. . . ]