User manual ASUS AP1600R

[. . . ] AP1600R Dual Intel® XeonTM 533MHz FSB 1U Rackmount Server User Guide Disclaimer/Copyrights No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. [. . . ] Both the front and rear panels have location switch and LED. To turn OFF the LED, press the location switch again or use the ASWM software. The location switch and LED are for service purposes. When the system fails or is shut down, the server administrator can press either the front or the rear location switch to identify the location of the specific 1U system in a rack cabinet. ASUS AP1600R 1U Rackmount Server 17 1. 5 Internal Features The standard components inside the AP1600R server include the motherboard, backplane, bridge board, fans and fan modules, and power supply. The pictures below show the standard components of the server. 1 10 11 10 9 8 6 5 2 1 7 4 3 1. 6. HDD bays Backplane (underneath) Bridge board 1 x 40mm PCI fan 8 x 40mm System fans 2 x Copper CPU heatsinks 7. 350W PSU NOTE The PCI riser card / card bracket assembly and the airflow guide also come installed in the system but not shown in the above picture. Refer to sections "2. 3 Installing and removing the airflow guide" and "2. 8 Installing a PCI card" for details on these components. 18 Chapter 1: System Overview Chapter 2 This chapter describes the hardware setup procedures that you have to perform when installing system components. ASUS AP1600R-S5 1U Rackmount Server Hardware Setup 19 2. 1 Removing and installing the chassis cover Removing the cover 1. To release the cover, push the two latches outward, then slide the cover towards the rear for about half an inch. Lift the cover from the chassis. Installing the cover 1. Place the cover on top of the chassis leaving about half an inch gap from the front edge. Half-inch gap 2. Firmly hold down the cover and you slide it towards the front until it fits in place. 20 Chapter 2: Hardware Setup 2. 2 Motherboard Placement NOTE The motherboard and other internal components of the AP1600R-S5 server are already installed as indicated in section "1. 4 Internal Features". Refer to the motherboard user's manual for detailed technical information about the motherboard. Placement Direction When installing the motherboard, make sure that you place it into the chassis correctly. The edge with the external ports goes to the rear part of the chassis. Place this side towards the rear of the chassis NOTE You must remove the protruding screws (indicated by black circles above) on the rear panel high-density SCSI connector before installing or removing the motherboard. Otherwise, you cannot properly install or remove the motherboard. Motherboard Screws Place six (6) screws in the holes indicated by circles to secure the motherboard to the chassis. Doing so may damage the motherboard. ASUS AP1600R-S5 1U Rackmount Server 21 2. 3 Installing and removing the airflow guide The airflow guide comes installed in the system. You have to detach the airflow guide before you can install a CPU. Screws Airflow guide To detach the airflow guide, use a Phillips screwdriver to remove the two screws that secure the module to the base of the chassis. To re-install the airflow guide (after installing the CPU and heatsink), place it on top of the heatsink in the orientation shown above. Secure the airflow guide using two screws. NOTE You also have to remove the PCI riser card and card bracket assembly before installing a CPU. Refer to section "2. 8 Installing a PCI card" for instructions on how to remove the riser card assembly. 22 Chapter 2: Hardware Setup 2. 4 Installing CPU and heatsink The 604-pin Zero Insertion Force (ZIF) sockets on the PR-DLSR533 motherboard support dual Intel® XeonTM processors. This section tells you how to install a CPU. [. . . ] The metal brace holds the power supply unit in place. Carefully lift the power supply from the chassis. 42 Chapter 3: Powering Up Appendix A This appendix gives information on the 350W switching power supply that comes with the AP1600R-S5 server. ASUS AP1600R-S5 1U Rackmount Server Power Supply 43 A. 1 General Description The server comes with an SSI-type 350W ATX power supply with universal AC input that includes PFC and ATX-compliant output cables and connectors. The power supply has two internal cooling fans. [. . . ]