User manual ASUS AW1500-S5

[. . . ] ® AW1500-S5 Intel® Xeon Tower/5U Rackmount Workstation with 533MHz FSB support User's Manual Disclaimer/Copyrights No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. [. . . ] Failure to do so may cause you physical injury and damage motherboard components. Placement direction When installing the motherboard, make sure that you place it into the chassis in the correct orientation. The edge with external ports goes to the rear part of the chassis as indicated in the image below. Place this side towards the rear of the chassis Motherboard Screws Place nine (9) screws into the holes indicated by circles to secure the motherboard to the chassis. Do not overtighten the screws!Doing so may damage the motherboard. 2-4 ASUS AW1500-S5 2. 3 Installing the Central Processing Unit (CPU) In the event of conflict between this instruction and other references cited herein, instructions in this system manual takes precedence. 2. 3. 1 Overview The motherboard comes with dual surface mount 604-pin Zero Insertion Force (ZIF) sockets. The sockets are designed for the Intel Xeon Processor in the 604-pin package with 512KB L2 cache. The processor includes the Intel® NetBurstTM micro-architecture that features the hyperthreading technology, rapid execution engine, 533MHz system bus, and execution trace cache. Together, these attributes improve system performance by allowing higher core frequencies, faster execution of integer instructions, and data transfer rate of up to 4. 26 GB/s. Gold Mark XeonTM 533 Mhz Processor PP-DLW PP-DLW Socket 604 Note in the illustration that the CPU has a gold triangular mark on one corner. This mark indicates the processor Pin 1 that should match a specific corner of the CPU socket. Incorrect installation of the CPU into the socket may bend the pins and severely damage the CPU!The motherboard supports either one or two CPUs. If you are installing only one CPU, you MUST install it in CPU socket 1. Otherwise, the red motherboard LED will light up as warning. Use Prestonia CPUs with the same FSB speed when installing on both CPU sockets. CPU Socket 1 (outer socket) CPU Socket 2 (inner socket) User's Manual 2-5 2. 3. 2 Installing the CPU If you are installing only one CPU, install in CPU socket 1. Follow these steps to install a CPU. Locate the 604-pin ZIF sockets on the motherboard. Unlock the socket by pressing the lever sideways, then lift it up to at least 115° angle. Make sure that the socket lever is lifted up to at least 115° angle, otherwise the CPU does not fit in completely. 2. Position the CPU above the socket as shown. Carefully insert the CPU into the socket until it fits in place. Marked Corner The CPU fits only in one correct orientation. DO NOT force the CPU into the socket to prevent bending the pins and damaging the CPU! 4. When the CPU is in place, press it firmly on the socket while you push down the socket lever to secure the CPU. The lever clicks on the side tab to indicate that it is locked. 2-6 ASUS AW1500-S5 2. 3. 3 Installing the CPU heatsink with fan assembly The Intel® XeonTM processors require especially designed heatsink and fan assembly to ensure optimum thermal condition and performance. Make sure that the heatsink with fan assembly is properly installed on the motherboard. A tilted or improperly installed heatsink with fan assembly can cause damage to motherboard CPU socket and/or CPU. Follow these steps to install the CPU heatsink and fan. Follow these steps to install the CPU heatsink and fan. [. . . ] Affix each plastic rubber wheel unit by mounting its screws on designated slots at the bottom of the chassis. Make sure the screws are tightened accordingly. chassis roller-wheel brake locks All the chassis roller-wheels can be locked individually with its built-in chassis-roller wheel brake locks. A-2 ASUS AW1500-S5 Appendix B This appendix contains detailed hardware operation and specifications of the AW1500-S5 power modules. User's Manual Power Modules A-3 Power Supply Specifications Output Voltage Regulation Output Voltage +3. 33V +5V +12V -12V +5VSB Min (V) 3. 16 4. 8 11. 52 -11. 4 4. 8 Nom (V) Max (V) 3. 30 5. 00 12. 00 -12. 20 5. 00 3. 46 5. 25 12. 60 -13. 08 5. 25 Ripple/Noise 50mVp-p 50mVp-p 120mVp-p 120mVp-p 50mVp-p Output Current Capacity Output Voltage +3. 33V +5V +12V -12V +5VSB Min (A) 0. 5 2. 0 4. 0 0. 0 0. 1 Max (A) 24. 0 20. 0 30. 0 0. 5 2. 0 Max. Load (W) 79. 0 100. 0 360. 0 6. 0 10 Over-Voltage Protection (OVP) Voltage +3. 33V +5V +12V +12V +5Vsb Min (V) 3. 9 5. 7 13. 3 -13. 3 5. 7 Max (V) 4. 5 6. 5 15. 0 -15. 0 6. 5 A-4 ASUS AW1500-S5 Removing Power Supply Case The power supply module is secured in a power supply cradle that connects to various power supply connectors on the SCSI backplane, the motherboard, IDE, floppy and CD-ROM drives. To remove the power supply, follow these steps: Make sure that the power suppy cable is unplugged before performing this procedure. 1. [. . . ]