User manual ASUS B202

[. . . ] SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Contents Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Connect the USB/GAME module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2. 0 specification that supports up to 480 Mbps connection speed. USB connectors (10-1 pin USB56, USB78, USB910) USB910 USB+5V USB_P6USB_P6+ GND NC USB+5V USB_P9USB_P9+ GND 1 USB+5V USB_P10USB_P10+ GND NC M2N32 WS PRO ® USB56 M2N32 WS PRO USB 2. 0 connectors Never connect a 1394 cable to the USB connectors. Doing so will damage the motherboard! 7. These connectors are for IEEE 1394a ports. Connect the IEEE 1394a module cables to any of these connectors, then install the module to a slot opening at the back of the system chassis. IEEE 1394a port connectors (10-1 pin IE1394_1; 10-1 pin IE1394_2) USB+5V USB_P5USB_P5+ GND M2N32 WS PRO ® IE1394_1 1 IE1394_2 +12V TPB1+ GND TPA1+ 1 M2N32 WS PRO IEEE 1394a connector Never connect a USB cable to the IEEE 1394a connector. Doing so will damage the motherboard! ASUS M2N32 WS Professional USB+5V USB_P7USB_P7+ GND 1 USB78 1 USB+5V USB_P8USB_P8+ GND NC GND +12V TPB1GND TPA1- GND +12V TPB1GND TPA1+12V TPB1+ GND TPA1+ 2- 8. CPU, Chassis, and Power Fan connectors (4-pin CPU_FAN, 3-pin CHA_FAN1, 3-pin CHA_FAN2, 3-pin CHA_FAN3, 3-pin CHA_FAN4, 3-pin SPS_FAN1) The fan connectors support cooling fans of 350 mA ~ 2000 mA (24 W max. ) or a total of 1 A ~ 3. 48 A (41. 76 W max. ) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. Do not place jumper caps on the fan connectors! SPS_FAN1 CPU_FAN CPU_FAN CHA_FAN3 CHA_FAN1 GND CHA_FANPWR Rotation M2N32 WS PRO ® CHA_FAN2 CHA_FAN4 GND +12V x 2- Chapter 2: Hardware information GND +12V x M2N32 WS PRO Fan connectors CHA_FAN3 CHA_FAN4 GND CHA_FANPWR Rotation CHA_FAN1 CHA_FAN2 GND +12V Rotation GND CPU FAN PWR CPU FAN IN CPU FAN PWM SPS_FAN 9. Chassis intrusion connector (4-1 pin CHASSIS) This connector is for a chassis-mounted intrusion detection sensor or switch. Connect one end of the chassis intrusion sensor or switch cable to this connector. The chassis intrusion sensor or switch sends a high-level signal to this connector when a chassis component is removed or replaced. The signal is then generated as a chassis intrusion event. System warning speaker (4-pin SPEAKER) This 4-pin connector is for the chassis-mounted system warning speaker. The speaker allows you to hear system beeps and warnings. ATX power button/soft-off button (2-pin PWR) This connector is for the system power button. Pressing the power button turns the system on or puts the system in sleep or soft-off mode depending on the BIOS settings. Pressing the power switch for more than four seconds while the system is ON turns the system OFF. Reset button (2-pin RESET) This 2-pin connector is for the chassis-mounted reset button for system reboot without turning off the system power. · · · · ASUS M2N32 WS Professional 2- 2-0 Chapter 2: Hardware information This chapter describes the power up sequence and ways of shutting down the system. Powering up 3 Chapter summary 3. 1 3. 2 Starting up for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Powering off the computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 3 ASUS M2N32 WS Professional 3. 1 1. 5. Starting up for the first time After making all the connections, replace the system case cover. Connect the power cord to the power connector at the back of the system chassis. Connect the power cord to a power outlet that is equipped with a surge protector. [. . . ] When you select this option or if you press <F5>, a confirmation window appears. Select Exit & Save Changes or make other changes before saving the values to the non-volatile RAM. Discard Changes This option allows you to discard the selections you made and restore the previously saved values. After selecting this option, a confirmation appears. Select YES to discard any changes and load the previously saved values. - Chapter : BIOS setup This chapter describes the contents of the support CD that comes with the motherboard package. Software support 5 Chapter summary 5. 1 5. 2 Installing an operating system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]