User manual ASUS CG1330

[. . . ] SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Contents Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi CG1330 specifications summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If you want to connect a high-definition front panel audio module to this connector, make sure that the Front. Panel. Type item in the BIOS is set to [HD Audio]; if you want to connect an AC'97 front panel audio module to this connector, set the item to [AC97]. Make sure the audio device of Sound playback is Realtek High Definition Audio (the name may be different based on the OS). Control Panel > Sounds and Audio Devices > Sound Playback to configure the setting. Chapter 1: Product introduction · 1-32 13. ATX power connectors (24-pin EATXPWR, 4-pin ATX12V) These connectors are for an ATX power supply. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. ATX12V GND +12V DC GND +12V DC EATXPWR +3 Volts +12 Volts +12 Volts +5V Standby Power OK Ground +5 Volts Ground +5 Volts Ground +3 Volts +3 Volts Ground +5 Volts +5 Volts +5 Volts -5 Volts Ground Ground Ground PSON# Ground -12 Volts +3 Volts CG1330 ® CG1330 ATX power connectors · We recommend that you use an ATX 12 V Specification 2. 0-compliant power supply unit (PSU) with a minimum of 300 W power rating. This PSU type has 24-pin and 4-pin power plugs. If you intend to use a PSU with 20-pin and 4-pin power plugs, make sure that the 20-pin power plug can provide at least 15 A on +12 V and that the PSU has a minimum power rating of 300 W. The system may become unstable or may not boot up if the power is inadequate. Do not forget to connect the 4-pin ATX +12 V power plug; otherwise, the system will not boot up. Simultaneous output for YPbPr, AV, S, and RGB is not supported. Dual display table This table indicates two corresponding displays when you connect two monitors on any two of the following ports. · · · RGB · HDMI module ports HDMI TV (S-Video/ Video/YPbPr) · · · · · · 1-35 ASUS CG1330 Playback of HD DVD and Blu-Ray Discs The speed and bandwidth of the CPU/Memory, DVD player, and drivers will affect the playback quality. Following is a configuration example for your reference. Using the CPU/Memory of higher speed and bandwidth with the higher-version DVD player and drivers will upgrade the playback quality. Memory - 2 x 1GB of DDR2-800 (Dual channel mode). Playback. software. -. CyberLink. PowerDVD. V. 7. 3 File Format Non protected clips HD-DVD VC1 Blu-Ray MPEG2 Suitable resolution XP Vista 1920 x 1080p 1920 x 1080p 1920 x 1080i 1280 x 720p 1280 x 720p 1280 x 720p 1-36 Chapter 1: Product introduction ASUS. Q-Connector. (system. panel) You can use the ASUS Q-Connector to connect/disconnect chassis front panel cables in a few steps. Refer to the instructions below to install the ASUS Q-Connector. Connect the front panel cables to the ASUS Q-Connector. Refer to the labels on the Q-Connector to know the detailed pin definitions, then match them to the respective front panel cable labels. 2. Install the ASUS Q-Connector to the system panel connector, making sure the orientation matches the labels on the motherboard. 3. The front panel functions are now enabled. The figure shows the Q-Connector properly installed on the motherboard. ASUS CG1330 1-37 1-38 Chapter 1: Product introduction This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided. BIOS setup 2 2. 1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. ASUS EZ Flash 2 (Updates the BIOS using a floppy disk/ USB flash disk or the motherboard support CD/DVD. ) ASUS Update (Updates the BIOS in Windows® environment. ) 3. [. . . ] Press <Enter> to save the changes while exiting. Exit. &. Discard. Changes Select this option only if you do not want to save the changes that you made to the Setup program. If you made changes to fields other than System Date, System Time, and Password, the BIOS asks for a confirmation before exiting. Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press <F5>, a confirmation window appears. Select Exit & Save Changes or make other changes before saving the values to the non-volatile RAM. Discard. Changes This option allows you to discard the selections you made and restore the previously saved values. [. . . ]