User manual ASUS CG5290

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Contents Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Insert a formatted, high density 1. 44 MB floppy disk into the drive. Insert the Windows® 000 CD to the optical drive. To create a set of boot disks for Windows® 000: D:\bootdisk\makeboot a: e. Press <Enter>, then follow screen instructions to continue. - Chapter : BIOS setup assuming that D: is your optical drive. 2. Copy the original or the latest motherboard BIOS file to the bootable floppy disk. 2. 1. 2 ASUSEZFlashutility The ASUS EZ Flash feature allows you to update the BIOS without having to go through the long process of booting from a floppy disk and using a DOS-based utility. The EZ Flash utility is built-in the BIOS chip so it is accessible by pressing <Alt> + <F> during the Power-On Self Tests (POST). Visit the ASUS website (www. asus. com) to download the latest BIOS file for the motherboard and rename the same to MN-MX. ROM. Save the BIOS file to a floppy disk, then restart the system. Press <Alt> + <F> during POST to display the following. EZFlash starting BIOS update Checking for floppy. . . 4. Insert the floppy disk that contains the BIOS file to the floppy disk drive. When the correct BIOS file is found, EZ Flash performs the BIOS update process and automatically reboots the system when done. EZFlash starting BIOS update Checking for floppy. . . Start erasing. . . . . . . | Start programming. . . | Flashed successfully. Rebooting. · · Do not shut down or reset the system while updating the BIOS to prevent system boot failure!The utility displays the following message and automatically checks the floppy disk for the original or updated BIOS file. Bad BIOS checksum. Checking for floppy. . . When found, the utility reads the BIOS file and starts flashing the corrupted BIOS file. Bad BIOS checksum. Start flashing. . . DO NOT shut down or reset the system while updating the BIOS!Doing so can cause system boot failure! -6 Chapter : BIOS setup 4. Restart the system after the utility completes the updating process. RecoveringtheBIOSfromthesupportCD To recover the BIOS from the support CD: 1. Remove any floppy disk from the floppy disk drive, then turn on the system. The utility displays the following message and automatically checks the floppy disk for the original or updated BIOS file. Insert the support CD to the optical drive. Bad BIOS checksum. Checking for floppy. . . When no floppy disk is found, the utility automatically checks the optical drive for the original or updated BIOS file. The utility then updates the corrupted BIOS file. Bad BIOS checksum. Start flashing. . . 4. Restart the system after the utility completes the updating process. The recovered BIOS may not be the latest BIOS version for this motherboard. Visit the ASUS website (www. asus. com) to download the latest BIOS file. ASUS MN 1394 -7 2. 1. 5 ASUSUpdateutility The ASUS Update is a utility that allows you to manage, save, and update the motherboard BIOS in Windows® environment. [. . . ] Select OK to discard any changes and load the previously saved values. LoadSetupDefaults This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press <F5>, a confirmation window appears. Select Exit & Save Changes or make other changes before saving the values to the non-volatile RAM. ASUS MN 1394 -37 -38 Chapter : BIOS setup This chapter describes the contents of the support CD that comes with the motherboard package. Software support 3 3. 1 Installing an operating system This motherboard supports Windows® 2000/XP operating systems (OS). Always install the latest OS version and corresponding updates to maximize the features of your hardware. · Motherboard settings and hardware options vary. [. . . ]