User manual ASUS DVD-E616P1

[. . . ] DVD-E616P1 DVD-ROM Drive User Manual 1 Copyrights/Disclaimer Copyright © 2003 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. [. . . ] These instructions will help you avoid damaging the discs and your DVD-ROM drive. Cleaning a Disc Spray the disc with compressed air for about five seconds to get rid of the dust on a disc. Handling a Disc Hold a disc by the edges. Do not touch the disc surface. ASUS DVD-E616P1 User Manual 19 Technical Information Environmental Specifications Temperature Humidity Vibration Impact Operation: Storage: Operation: Storage: Operation: Storage: Non-operation: +5°C to +45°C - 20°C to +60°C 5% to 85% non-condensing 5% to 90% non-condensing 0. 25G peak at 10 ~ 300 Hz 1. 5G peak at 10 ~ 300 Hz 1 oct/min ­ no damage Less than 50G ­ (at 11ms/half sine wave, 3 shock/each side) 1 oct/min ­ no damage 60 cm high ­ (1 corner, 3 edges, 6 surfaces) Packaged: Acoustic Noise Less than 49dB (Without loading operation, on 1m hemisphere, with 0. 25 imbalance disc at 8, 600 rpm. ) MTBF: 100, 000 power on hours 30 minutes Reliability Mean Time To Repair (MTTR) Electrical and Audio Specifications Power Source I/O Terminal Voltage Tolerance Power connector ATAPI terminal Audio out No. of channels Sampling frequency Quantization Distortion S/N ratio Output: Line Out +5V DC +/- 5% +12V DC +/- 10% 4-pin +5V, +12V 40-pin 4-pin (analog) 2 (stereo) 44. 1 kHz 16 bits 0. 2% max. (at 1 kHz) 70 dB 0. 7 V rms (typical) Audio 20 ASUS DVD-E616P1 User Manual DVD Region Codes Region codes are part of the DVD standard. However, Region code on DVD discs are optional. DVD discs with no specified region code can be played on all DVD players. The world is set up into regions according to DVD titles. There are six regions around the world as illustrated by the map below. This DVD drive can be changed to play a DVD from any region in the world but can ONLY be changed five times. This restriction makes the drive adaptable for use in any region while still maintaining compliance with RPC-II regulations. The ability to switch from one region to another is not an ongoing feature. Please set the drive to your local region only or you may risk setting the drive permanently for a region that is not compliant with the media available in your part of the world. Region Code 1 2 3 4 5 6 U. S. , U. S. Territories, Canada Area Europe, Middle East, Japan, Egypt, S. Africa, Greenland South Eastern Asia, Taiwan, Hong Kong, Korea Australia, New Zealand, Latin America, Pacific Islands (former Russia), Eastern Europe, India, Africa, North Korea China ASUS DVD-E616P1 User Manual 21 22 ASUS DVD-E616P1 User Manual DVD-E616P1 DVD-ROM Drive Quick Installation Guide In 12 Languages 23 Quick Installation Guide Hardware Installation 1. Turn off your computer and any peripheral devices connected to it. Use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, before handling the device to avoid damaging it due to static electricity. Configure the DVD-ROM drive jumpers to set the device to master or slave mode before installing it into the chassis. Use jumper blocks to short the pins to your desired setting. Insert the DVD-ROM drive into an available 5. 25-inch bay. Connect a 4-pin power supply cable to the DC input connector of the DVD-ROM drive. Connect one end of the IDE ribbon cable to the IDE connector at the back of the DVD-ROM drive, matching the colored stripe on the cable with Pin 1 on the IDE connector. Connect the other end of the IDE cable to the IDE connector on the motherboard. Connect one end of the 4-pin audio cable to the audio output connector of the DVD-ROM drive. [. . . ] Använd bygelblock för att ställa in stiften på önskat vis. Sätt i DVD-ROM-enheten i ett ledigt 5, 25-tums fack. Anslut en 4-stifts strömkabel till likströmsingången på DVD-ROMenheten. Anslut ena änden av IDE-bandkabeln till IDE-anslutningen på baksidan av DVD-ROM-enheten, och matcha färgranden på kabeln med stift 1 på IDE-anslutningen. [. . . ]