User manual ASUS E742

[. . . ] 6 Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 TCP/IP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Front Panel Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If your system does not have an embedded LAN controller, you must install a network interface card as instructed below (assuming that you are using an Ethernet card under the operating system of Windows 98): 1. Install an Ethernet card on your motherboard. Power up your PC and follow the Add New Hardware Wizard's instructions to install the driver. When asked to restart your computer at the end of the installation, click Yes. After restarting the system, right-click My Computer on the desktop, select Properties, click the Device Manager tab, and then double-click Network adapters to confirm that the Ethernet driver is properly installed. 6 Wireless Cable Modem User's Manual Preparations TCP/IP Settings After the TCP/IP protocol is installed, restart your computer and consult the installation guide provided by your cable operator to complete TCP/IP configurations. Wireless Cable Modem User's Manual 7 Using the Wireless Cable Modem Front Panel 1 2 3 4 5 POWER STATUS CABLE PC USB 8 Wireless Cable Modem User's Manual Using the Wireless Cable Modem Front Panel Indicators LED Indicator 1. 2. 100 6. 7. 8. State ON Flashing OFF ON OFF ON Flashing OFF ON OFF ON OFF ON Flashing ON Flashing ON Flashing OFF ON OFF Description Wireless LAN Card is ready Data transmitting between cable modem and wireless network ------ Modem is powered ON Modem is powered OFF (if adapter connected, use correct adpater. ) Ethernet link is ready Data transmitting between cable modem and ethernet network ------ Full duplex Half duplex 100 BaseTX 10 BaseT No traffic Data transmitting between cable modem and cable operator's network Downstream channel has been locked Searching for Downstream channel Modem successfully registered on cable operator's network Modem is registering on cable operator's network --------------Error (Try resetting modem; if still error, contact customer support) Normal operation Wireless Cable Modem User's Manual 9 Using the Wireless Cable Modem Rear Panel 1 2 3 4 5 6 DC +5V/2. 5A Cable Console Reset USB 10/100-BaseT 1. DC +5V/2. 5A Power Input Jack The provided power adapter converts AC power to DC power for use with this jack. Power supplied through this jack will supply power to the cable modem. RF Connector The connector may be located right next to the power input jack or the serial port. The F-Type female connector allows cable data communication between the cable modem and the cable service provider through a coaxial cable. Reset Switch The reset button, when pressed, resets the cable modem without the need to unplug the power cord. Serial Port The 9-pin D-sub serial port supports the RS-232 terminal interface for advanced cable modem management. 10/100-BaseT LAN Ports The LAN ports support 10Base-T or 100Base-TX networks. These ports allow your PC or Ethernet hub to be connected to the cable modem through a CAT. 5 twisted pair LAN cable. 10 Wireless Cable Modem User's Manual Using the Wireless Cable Modem Installing the Wireless Cable Modem Take the following steps to accomplish the installation procedure: 1. Connect the cable TV coaxial cable to the input connector of a signal splitter. Connect a coaxial cable from one of the output connectors on the splitter to the input connector of your TV set. Use another coaxial cable to connect the other output connector on the splitter and the RF connector on the rear panel of the wireless cable modem. Connect the LAN cable from the LAN port on your computer to the LAN port on the rear panel of the wireless cable modem. You can also connect to a PC with wireless PC card (see "Configuring Wireless Settings") 5. Connect the AC power adapter to the DC +5V/2. 5A input jack on the rear panel of the wireless cable modem. Plug in the AC power adapter to an electrical outlet. [. . . ] To have the communication with CMTS, please click the "Disable" WLAN Enable: "Disable" means the Wireless cable modem works only as a normal cable modem without active the wireless functions. To have the communication with Wireless station, please click the "Enable" If you want to save the configuration data, please click Apply button and afterwards it will become default configuration. After change the new parameters to the Wireless Cable modem, you need to reset the modem to active the new settings. 14 Wireless Cable Modem User's Manual Wireless Settings WEP Settings WEP Manual: "Automatic" Passphrase:To generate the key, if the WEP is enabled. This is the code used while a wireless point is to log on to the network thru the WEP encryption function. [. . . ]