User manual ASUS E976

[. . . ] E976 ® DVD-ROM Drive ATAPI / Enhanced IDE Interface USER'S MANUAL Copyrights/Disclaimer Copyright © 2002 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. [. . . ] The DIR command does not work with audio CD discs while in DOS. You can use the command, however, to display the directory on a data CD. NOTE: You can use the DIR command to display the directory on an audio disc while in Windows using the command prompt or MS-DOS Prompt. Refer to your Windows manual on how to find the command prompt. DVD-ROM Specific Problems PROBLEM CAUSE SOLUTIONS Cannot play any DVD movie. You may not have an MPEG-2 card and/or decoder software installed on your computer system. 1. Install an MPEG-2 card. To install an MPEG-2 card, you need at least a 166MHz Pentium, AGP motherboard, 32MB system memory, and Windows 95 OSR2. 2. Install a software-only DVD decoder. To install a software-only DVD decoder, you need at least a 300MHz Pentium II, AGP motherboard, 32MB system memory, AGP graphics card, sound card supporting 48MHz sample rate, and Windows 95 OSR2 with USB upgrade. V. Troubleshooting 16 3. Contact your dealer for more information. PROBLEM When playing a DVD movie, I get an error message about an invalid country or region code. CAUSE DVD movies are regionally coded so you may be trying to play a DVD movie from a region other than the one specified for your MPEG-2 card or DVD player software. SOLUTION Check your DVD movie to see which Region Code it has then purchase an MPEG-2 card and/or DVD player software specific for that region. ASUS High-Speed DVD-ROM Drive ENGLISH QUICK INSTALLATION GUIDE I. Turn off your computer and peripheral devices, such as your printer. If you do not have one, touch both of your hands to a safely grounded object or to a metal object on your system. Set your drive as either the Master or Slave (default) drive by placing the jumper cap on the desired jumper. Insert the DVDROM Drive into one of the free 5. 25-inch bays available for disk drives. Connect an unused power supply cable to the back of your DVDROM Drive. Connect the 40-pin IDE ribbon cable to the back of your DVDROM Drive. Make sure that the red stripe on the cable is aligned to Pin 1 of the IDE connector. If you have a sound card, connect the 4-pin CD audio cable to the DVDROM Drive's Analog Audio line out connector. If you do not have a sound card, plug earphones, headphones, or powered/self-amplified speakers to the Headphones Jack on your DVDROM's front panel. Set the volume controls of your drive and powered/selfamplified speakers to minimum before starting or restarting your computer. If you removed any drive or other items other than your DVDROM Drive, put them back into place and secure them to your computer. Slide your DVDROM Drive now into place and fasten it to your system with the screws provided. [. . . ] Ställ in volym av din enhet och högtalarna med separat elkällan på minimum innan du startar elle startar om din dator. Om du har tagit bort några enheter eller andra delar förutom DVDROM-enheten, återplacera dem och kontrollera att dem sitter fast. Sätt in din DVDROM-enhet i utrymmet och fastskruva den till systemet med de befintliga skruvorna. Återplacera luckan på din dator och fastskruva den med de skruvor som du har tagit bort innan. [. . . ]