User manual ASUS EB1501P

[. . . ] Specifications and information contained in this manual ae furnished for informational use only, and are subject to change at any time without notice, and should not be construed as a commitment by ASUS. ASUS assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual, including the products and software described in it. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Contents Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Failure to do so may cause you physical injury and may damage motherboard components. The motherboard is secured to the chassis by ten screws as indicated by circles in the illustration below. Refer to the motherboard user guide for detailed information on the motherboard. 2-4 Chapter 2: Hardware setup 2. 4 Installing a Central Processing Unit (CPU) 2. 4. 1 Overview The motherboard comes with a surface mount 478-pin Zero Insertion Force (ZIF) socket. The socket is designed for the Intel® Pentium® 4 Prescott processor in the 478-pin package with 512KB L2 cache. The motherboard supports 800/533/400MHz front side bus (FSB), and allows data transfer rates of up to 6. 4GB/s. Note in the illustration that the CPU has a gold triangular mark on one corner. This mark indicates the processor Pin 1 that should match a specific corner of the CPU socket. Gold Arrow ® P4P800S-E P4P800S-E Socket 478 Incorrect installation of the CPU into the socket may bend the pins and severely damage the CPU! ASUS EB1501P user guide 2-5 2. 4. 2 CPU installation Follow these steps to install a CPU. Locate the 478-pin ZIF socket on the motherboard. 2. Unlock the socket by pressing the lever sideways, then lift it up to a 90°-100° angle. Make sure that the socket lever is lifted up to 90°-100° angle, otherwise the CPU does not fit in completely. Socket Lever 90 - 100 3. Position the CPU above the socket such that its marked corner matches the base of the socket lever. Carefully insert the CPU into the socket until it fits in place. The CPU fits only in one correct orientation. DO NOT force the CPU into the socket to prevent bending the pins and damaging the CPU! Gold Mark 5. When the CPU is in place, push down the socket lever to secure the CPU. Place the HDD cage in a flat surface. 2. Insert a HDD to the upper bay of the cage. Make sure that the HDD screw holes are aligned with the HDD cage screw holes (with black rubber stoppers). DO NOT install a hard disk drive to the lower bay of the cage. 3 4 3. Secure the HDD to the cage with two screws (with metal washers) on both sides of the cage. 4. Align the HDD cage and bay assembly rails, then carefully push the HDD cage until it is flushed to the chassis. 2-11 ASUS EB1501P user guide 5 6 5. Connect a 40-pin IDE cable to the IDE connector at the back of the drive. 6. Connect a 4-pin power plug from the power supply unit to the power connector at the back of the drive. Refer to the motherboard user guide the correct IDE cable before connecting anIDE cable to the hard disk drive. To install a Serial ATA hard disk drive: 1. Follow steps 1-4 of the previous section. Connect one end of the supplied 7-pin SATA cable to the SATA connector at the back of the drive, then connect the other end to a SATA connector on the motherboard. See page 3-6 for the location of the SATA connectors. [. . . ] Locate two retention bracket screw holes on the chassis floor. 2 3. Place the retention bracket over the chassis floor screw holes, then secure the bracket with two screws. Turn the chassis upright. 3 ASUS EB1501P user guide 3-7 To install the expansion card holder: 1. Insert the expansion card holder locking screw to the retention bracket notch, as shown. 1 2. [. . . ]