User manual ASUS ES5000 ES5000/ES5000P USER’S MANUAL(ENGLISH)

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. [. . . ] The values range from 0. 80V to 1. 70V with a 0. 00625V interval. Chapter 3 3-18 CPU PLL Voltage [Auto] Allows you to set the CPU and PCH PLL voltage. The values range from 1. 20V to 2. 20V with a 0. 00625V interval. Chapter 3: BIOS setup PCH Voltage [Auto] Allows you to set the Platform Controller Hub voltage. The values range from 0. 80V to 1. 70V with a 0. 01V interval. • The values of the CPU PLL Voltage, CPU Manual Voltage, CPU Offset Voltage, iGPU Manual Voltage, iGPU Offset Voltage, DRAM Voltage, VCCSA Voltage, VCCIO Voltage, and PCH Voltage items are labeled in different color, indicating the risk levels of high voltage settings. The system may need better cooling system to work stably under high voltage settings. When you enable the OV_CPU/DRAM jumper, the CPU Manual Voltage and DRAM Voltage increases to a maximum 2. 3V range. • • DRAM DATA REF Voltage on CHA/B [Auto] Allows you to set the DRAM DATA Reference Voltage on Channel A/B. The values range from 0. 395x to 0. 630x with a 0. 005x interval. Different ratio might enhance DRAM overclocking ability. DRAM CTRL REF Voltage on CHA/B [Auto] Allows you to set the DRAM Control Reference Voltage on Channel A/B. The values range from 0. 395x to 0. 630x with a 0. 005x interval. Different ratio might enhance DRAM overclocking ability. CPU Spread Spectrum [Auto] [Auto] [Disabled] [Enabled] Automatic configuration. Enhances the BCLK overclocking ability. Sets to [Enabled] for EMI control. BCLK Recovery Allows you to recover the BCLK parameters. Configuration options: [Auto] [Enabled] [Disabled] ASUS ES5000 3-19 Chapter 3 3. 5 The Advanced menu items allow you to change the settings for the CPU and other system devices. Be cautious when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction. UEFI BIOS Utility - Advanced Mode Exit Advanced menu Main Ai Tweaker Advanced Monitor Boot Tool > CPU Configuration > PCH Configuration > SATA Configuration > System Agent Configuration > USB Configuration > Onboard Devices Configuration > APM > Network Stack CPU Configuration Parameters →←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. Configuration options: [Immediately] [1 minute] [2 minutes] [5 minutes] [10 minutes] [15 minutes] [30 minutes] [1 hour] [2 hours] Active Page Threshold Support [Enabled] Active Memory Threshold [0] The system automatically set itself to sleep when the partition size is not enough for Rapid Start Technology to work. Configuration options: [Enabled] [Disabled] Key in the value for the additional partition size for Rapid Start Technology to work. Ensure that the caching partition size is larger than the total memory size. 3. 5. 3 While entering Setup, the BIOS automatically detects the presence of SATA devices. The SATA Port items show Not Present if no SATA device is installed to the corresponding SATA port. Scroll down to display the other BIOS items. UEFI BIOS Utility - Advanced Mode SATA Configuration Exit Main Back Ai Tweaker Advanced\ SATA Configuration > Advanced Monitor Boot Tool SATA Configuration SATA Mode Selection S. M. A. R. T. Status Check SATA 6G_1 (Gray) Hot Plug SATA 6G_2 (Gray) Hot Plug SATA 3G_3 (Blue) Hot Plug SATA 3G_4 (Blue) Hot Plug SATA 3G_5 (Blue) Hot Plug MSATA (Black) AHCI Enabled Not Present Disabled Not Present Disabled Not Present Disabled Not Present Disabled Not Present Disabled Not Present (1) IDE Mode. (3) RAID Mode. →←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F5: Optimized Defaults F10: Save ESC: Exit F12: Print Screen Version 2. 00. 1208. Copyright (C) 2012 American Megatrends, Inc. Chapter 3 3-24 Chapter 3: BIOS setup SATA Mode Selection [AHCI] [Disabled] [IDE] Allows you to set the SATA configuration. [AHCI] Set to [IDE Mode] when you want to use the Serial ATA hard disk drives as Parallel ATA physical storage devices. Set to [AHCI Mode] when you want the SATA hard disk drives to use the AHCI (Advanced Host Controller Interface). The AHCI allows the onboard storage driver to enable advanced Serial ATA features that increases storage performance on random workloads by allowing the drive to internally optimize the order of commands. Disables the SATA function. [RAID] Set to [RAID Mode] when you want to create a RAID configuration from the SATA hard disk drives. S. M. A. R. T. (Self-Monitoring, Analysis and Reporting Technology) is a monitor system. [. . . ] Consult the dealer or an experienced radio/TV technician for help. The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. ASUS ES5000 A-1 Appendices IC: Canadian Compliance Statement Complies with the Canadian ICES-003 Class B specifications. This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations. [. . . ]