User manual ASUS ET2400IN-512M

[. . . ] The power supply cord serves as a power disconnect device for pluggable equipment. The socket outlet shall be installed near the equipment and shall be easily accessible. Disclaimer Safety Instructions English 1 Benq LCD Color Monitor User's Guide Table of Contents Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Views of the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] LCD monitor with undetachable signal cable Quick Start Guide CD-ROM Power cord Extension Base English 3 Benq LCD Color Monitor User's Guide Views of the Monitor Front View Back View (1) English 4 Benq LCD Color Monitor User's Guide Back View (2): Locations of plugs & sockets 1. Video cable English 5 Benq LCD Color Monitor User's Guide Installation Hardware Installation A. Make sure that the computer and monitor's power are both turned off. Please follow the steps to install your LCD monitor. 1 . Connect the power cord to ASUS LCD monitor. B. Connect the signal cable to the VGA output of the graphics card on the computer. Connect the power cord at the back of the monitor to an AC power socket. Please make sure that the socket is not blocked or covered, so you can disconnect the unit from AC supply if you need to. Your monitor is equipped with an automatic power supply for a voltage range from 100 to 240 Volt at a frequency of 50 to 60 Hz. Be sure that your local power is within the supported range. If you are unsure, ask your electricity supplier. Signal Power cord English 6 Benq LCD Color Monitor User's Guide Adjusting the Monitor A Look at the Control Panel ikey Exit < > Enter There are 6 keys for user's control including "iKey", "Exit", "Enter", "<" and ">" key and a power swith. The following descriptions are the introduction of these keys & switch. There are three items for miscellaneous. OSD Position : to adjust position of OSD. English 36 Benq LCD Color Monitor User's Guide Language: to select OSD language. OSD Time: to set the standby time of OSD. H. (Horizontal) Position: adjusts the OSD horizontal position of the display. V. (Vertical) Position: adjusts the OSD vertical position of the display. Press "<"or ">"key to select a language then press "Exit" to back to previous menu. English 37 Benq LCD Color Monitor User's Guide 5. Information "Information" sub menu the OSD display the resolution, horizontal and vertical refresh rate. Press "Enter" to recall to factory setings. English 38 Benq LCD Color Monitor User's Guide Troubleshooting Frequently Asked Questions (FAQ) The image is blurred:  Read the chapter, Installation/Adjustment and then select the correct resolution, refresh rate and make adjustments based on these instructions.  Do you use a VGA extension cable?Remove the extension cable for the test. If not, optimize the image working on the description in the chapter, Installation/Adjustment. It is normal for blurring to occur due to conduction losses in extension cables. You can minimize these losses by using an extension cable with better conduction quality or with a builtin booster.  Does the blurring only occur at resolutions lower than the native (maximum) resolution?Read the chapter Installation/Adjustment. Pixel errors can be seen:  One of several pixels are permanently black, one or more pixels are permanently white, one or more pixels are permanently red, green, blue or another colour. Read the chapter Pixel error rates. [. . . ] If that does not help, then check the VGA cable contacts. If any pins are bent or broken off, then contact your dealer or read the chapter, Additional Help, Repairs & Service.  Is the prompt on the display not illuminated at all?Check the power supply mains socket, the external power supply and the mains switch. English 39 Benq LCD Color Monitor User's Guide The image is or distorted, flashes or flickers:  Read the chapter, Installation/Adjustment and then select the correct resolution, refresh rate and make adjustments based on these instructions. The image is displaced in one direction:  Read the chapter, Installation/Adjustment and then select the correct resolution, refresh rate and make adjustments based on these instructions. Need More Help? If your problems remain after checking this manual, please contact your place of purchase or e-mail us at: DPLservice@benq. com English 40 Benq LCD Color Monitor User's Guide Supported operating modes Incoming display mode (Input timing) Resolution 640x350 720x400 640x480 640x480 640x480 800x600 800x600 800x600 800x600 1024x768 1024x768 1024x768 Horizontal Frequency (KHz) 31. 47(P) 31. 47(N) 31. 47(N) 37. 86(N) 37. 50(N) 35. 16(P) 37. 88(P) 48. 08(P) 46. 87(P) 48. 36(N) 56. 48(N) 60. 02(P) Vertical Frequency (Hz) 70. 08(N) 70. 08(P) 60. 00(N) 72. 80(N) 75. 00(N) 56. 25(P) 60. 32(P) 72. 19(P) 75. 00(P) 60. 00(N) 70. 10(N) 75. 00(P) Pixel Frequency (MHz) 25. 17 28. 32 25. 18 31. 50 31. 50 36. 00 40. 00 50. 00 49. 50 65. 00 75. 00 78. 75 Comment DOS DOS DOS VESA VESA VESA VESA VESA VESA VESA VESA VESA hModes, which are not listed in the above table, may not be supported. [. . . ]