User manual ASUS ET2400XVT

[. . . ] Please read this user's manual carefully before operating this product. To ensure proper operation, please read and follow ALL the instructions, especially the "IMPORTANT SAFETY INSTRUCTIONS" and "SAFETY PRECAUTIONS". Please keep this user's manual for future reference. Ver. 1 ENGLISH CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . 1 INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If you have to change the power cord, please use a certified power cord that meets your region's safety standards. 17 BASIC OPERATION ENGLISH Front Rear Power On/Off Turn On the power of the unit. To turn On the power to the unit: 1. The Indicating Lamp illuminates in Green, and the Illumination Lamp turns into Blue. The image will display on screen. Illumination Lamp Indicating Lamp 2. Once the Power switch is on, you can turn On/Off by pressing the Power (On/Off, On, Off) button on the remote control. Power Switch (on the underside) To turn Off the power to the unit: 1. Press the Power (On/Off, Off) button on the remote control. The Indicating Lamp turns into Red (Standby mode), and the Illumination Lamp turns off. Press the Power switch on the unit to completely turn Off the power to the unit. NOTE Power On/Off button Power Off button Whilst the Indicating Lamp illuminates in Red (Standby mode), you can turn On/Off by pressing the Power (On/Off, On, Off) button on the remote control. Power On button The Indicating Lamp/Illumination Lamp Status Indicating Lamp Off Red Green Orange NOTE Illumination Lamp ­ ­ Blue ­ Power Status Off Standby mode On Power Save mode Refer to 32 Remark ­ ­ ­ and 33 for the condition. Whenever the monitor receives signal from the remote control, the indicating lamp blinks in green. If the image does not appear on the screen at all, or if there is any problem with it, see "TROUBLESHOOTING" on 33 ~ 35 . This may help you to solve the problems. After turning On, it takes about 6 seconds until the monitor starts up. Please note that buttons on the remote control and the unit (such as the Power button) do not work during this period of time. Press the button on the remote control or the Menu button on the control panel of the unit. The Main Menu is displayed on the screen as shown on the right. The selected item will be highlighted in Yellow. Press the OK button to set your selection. The selected menu page will be displayed on the screen. Use the Picture Audio Function Setup Language Select OK Set <Main Menu> Menu button button to choose the item on the menu page. OK button to set your selection. button to adjust the item values or choose options. To exit from the menu, press the NOTE The OSD menu screen will be closed automatically when no operation has been made for about one minute. If the item on the menu is shown in grey, it means that it cannot be selected or adjusted. Menu button Select Language Select the language from the list so that the OSD menu can be displayed in the selected language. How to set Language Language 1. Enter the "Language" menu from the Main Menu. Select your preferred language from the list using the The selected item will be highlighted in Yellow. button. English English (US) Français Español Deutsch 3. Press the OK button to set your selection. [. . . ] 42 inches (930 (H) x 523 (V) mm, diagonal 1067mm) Operating: 5ºC to 35ºC Operating: 20% to 80% AC220-240V, 50Hz 132W/<0. 8W speaker 6W + 6W Approx. 37 inches (820 (H) x 461 (V) mm, diagonal 941mm) Operating: 5ºC to 35ºC Approx. 32 inches (698 (H) x 392 (V) mm, diagonal 801mm) Net Weight UT32MH70U/E Net Weight UT37MX70U/E Net Weight UT42MX70U/E The unit takes at least 30 minutes to attain the status of optimal picture quality. * This Analogue Audio Input terminal can be used for PC (RGB) or HDMI-DVI. PRODUCT SPECIFICATIONS (continued) Signal Input RGB terminal (D-sub 15 pin connector) Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Input signal R G/Composite B No connection No connection R. GND G. GND/Composite. GND B. GND +5V GND No connection [SDA] H. sync V. sync. [. . . ]