User manual ASUS GIGAX 2024M

[. . . ] GigaX2024B/M Layer 2 Managed Switch CLI Manual E2644 May 2006 V1 No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS provides this manual "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASUS, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of use or data, interruption of business and the like), even if ASUS has been advised of the possibility of such damages arising from any defect or error in this manual or product. [. . . ] ASUS(config-if)# gvrp registration fixed 4. 5 Syntax show gvrp show gvrp configuration IFNAME gvrp General Attribute Registration Protocol Parameters Default Description Example Command Mode Privileged EXEC mode To show gvrp configuration status. ASUS#show gvrp 4. 6 Syntax show gvrp statistics [IFNAME] show gvrp statistics [IFNAME] gvrp statistics General Attribute Registration Protocol the GVRP statistics Parameters [IFNAME] Interface's name, ex: fastethernet1/0/1 or gigabitethernet1/0/26 Command Mode Privileged EXEC mode 10 GigaX2024B/M L2 Managed Switch CLI Manual Default Description Example To show gvrp statistics IFNAME status. ASUS# show gvrp statistics fa1/0/1 4. 7 Syntax showgvrpinterfaceIFNAME show gvrp interface IFNAME gvrp General Attribute Registration Protocol [IFNAME] Interface's name, ex: fastethernet1/0/1 or gigabitethernet1/0/26 Parameters Command Mode Privileged EXEC mode Default Description Example To show gvrp port status. ASUS#show gvrp interface fa1/0/1 2 4. 8 Syntax garp join-timer <1-100000000> garp join-timer <1-100000000> join-timer <1-100000000> Join timer the timer values Parameters Command Mode Interface mode No/clear Show Default Description Example no garp join-timer show garp timer IFNAME The default is 20 (centi-seconds) This command sets the garp join-timer value in the indicated interface port. ASUS(config-if)#garp join-timer 20 4. 9 Syntax garp leaveall-timer <1-100000000> garp leaveall-timer <1-100000000> leave-timer <1-100000000> Leave timer the timer values 11 Parameters GigaX2024B/M L2 Managed Switch CLI Manual Command Mode Interface mode No/clear Show Default Description Example no garp leaveall-timer show garp timer IFNAME The default is 1000 (centi-seconds) This command sets the garp leaveall-timer value in the indicated interface port. ASUS(config-if)#garp leaveall-time 2000 4. 10 garp leave-timer <1-100000000> Syntax Parameters garp leave-timer <1-100000000> leaveall-timer <1-100000000> Command Mode Interface mode No/clear Show Default Description Example no garp leave-timer show garp timer IFNAME The default is 60 (centi-seconds) This command sets the garp leave-timer value in the indicated interface port. ASUS(config-if)#garp leave-timer 60 Leaveall timer the timer values 4. 11 show garp timer IFNAME Syntax Parameters show garp timer IFNAME timer [IFNAME] the setting timer values (join, leave, and leaveall timer) Interface's name, ex: fastethernet1/0/1 or gigabitethernet1/0/26 Command Mode Privileged EXEC mode Default Description Example To show garp timer IFNAME status. ASUS# show garp timer fa1/0/1 12 GigaX2024B/M L2 Managed Switch CLI Manual 5. 5. 1 Syntax VLAN: show vlan name VLANAME show vlan name VLANAME VLANAME vlan name None or depends on ODM customer Use the show vlan user EXEC command to display the parameters for all configured VLANs or one VLAN (if the VLAN ID or name is specified) on the switch. ASUS#show vlan name VLAN1 Parameters Default Description Command Mode Privileged EXEC mode Example 5. 2 Syntax vlan <2-3000> vlan <2-3000> vid vlan id no vlan <2-3000> None or depends on ODM customer Use the vlan vid command to create vlan entry on the switch. ASUS(config)#vlan 2 Parameters No/clear Default Description Example Command Mode Global configuration mode 5. 3 Syntax show vlan [VLANID] show vlan [VLANID] [VLANID] vlan id None or depends on ODM customer Use the show vlan user EXEC command to display the parameters for all configured VLANs or one VLAN (if the VLAN ID or name is specified) on the switch. ASUS#show vlan 2 13 Parameters Default Description Command Mode Privileged EXEC mode Example GigaX2024B/M L2 Managed Switch CLI Manual 5. 4 Syntax name VLANAME name VLANAME VLANAME - vlan name string no name None or depends on ODM customer Use the name string command to create vlan entry with string on the switch. ASUS(config-vlan)#name ABC Parameters No/clear Default Description Example Command Mode Config-vlan mode 5. 5 Syntax switchport access vlan <1-3000> switchport access vlan <1-3000> access vlan the interface in access mode Virtual LAN Parameters <1-3000> valid vlan-id range is 1 to 3000 Command Mode Interface mode No/clear Show Default Description Example no switchport access vlan show vlan [VLANID] None or depends on ODM customer Set access mode characteristics of all interfaces and Set Virtual LAN ASUS(config-if)#switchport access vlan 2 5. 6 Syntax switchport mode (access|trunk) switchport mode (access|trunk) access trunk the interface in access mode the interface in trunk mode Parameters Command Mode Interface mode No/clear no switchport access vlan 14 GigaX2024B/M L2 Managed Switch CLI Manual Show Default Description Example show interface [IFNAME] None or depends on ODM customer Set access mode characteristics of all interfaces and Set Virtual LAN ASUS(config-if)#switchport mode access 5. 7 Syntax switchport trunk native vlan <1-3000> switchport trunk native vlan <1-3000> trunk native vlan the interface in trunk mode untag vlan Virtual LAN Parameters <1-3000> valid vlan-id range is 1 to 3000 Command Mode Interface mode No/clear Show Default Description Example show vlan [VLANID] None or depends on ODM customer Set native vlan of the port ASUS(config-if)#switchport trunk native vlan 2 5. 8 switchport trunk allowed vlan (add|remove) VLANLIST Syntax Parameters switchport trunk allowed vlan (add|remove) VLANLIST trunk trunk characteristics allowed the allowed VLANs that can receive and send traffic on this interface in tagged format when in trunking mode vlan add remove the allowed VLANs to add the list of allowed VLANs to remove the list of allowed VLANs VLANLIST valid format is vlan_atom, [, vlan_atom. . . ], [-vlan_atom, . . . ], . . . 15 GigaX2024B/M L2 Managed Switch CLI Manual Command Mode Interface mode No/clear Show Default Description switchport trunk allowed vlan remove VLANLIST show vlan [VLANID] None or depends on ODM customer Use the switchport trunk allowed vlan configuration command on the switch stack or standalone switch to add or remove the allowed VLANs that can receive and send traffic on this interface in tagged format when in trunking mode ASUS(config-if)# switchport trunk allowed vlan add 2-20 Example 6. 6. 1 Syntax 802. 1x: dot1xguest-vlan<1-3000> dot1x guest-vlan <1-3000> <1-3000> valid vlan-id range is from 1 to 3000 no dot1x guest-vlan show dot1x all / show dot1x interface IFNAME No default guest vlan Use the dot1x guest-vlan interface configuration command on the switch stack or on a standalone switch to specify an active VLAN as an 802. 1X guest VLAN. Use the no form of this command to return to the default setting. ASUS(config-if)#dot1x guest-vlan 2 Parameters No/clear Show Default Description Command Mode Interface mode Example 6. 2 Syntax dot1xmax-req<1-10> dot1x max-req <1-10> <1-10> max-req times ; valid values are from 1 to 10 Parameters No/clear Show 16 Command Mode Interface mode no dot1x max-req show dot1x all GigaX2024B/M L2 Managed Switch CLI Manual Default Description The default is 2 Use the dot1x max-req interface configuration command on the switch stack or on a standalone switch to set the maximum number of times that the switch sends an Extensible Authentication Protocol (EAP)-request/identity frame (assuming that no response is received) to the client before restarting the authentication process. Use the no form of this command to return to the default setting. ASUS(config-if)#dot1x max-req 2 Example 6. 3 dot1x port-control (auto|force-authorized| force-unauthorized) Syntax Parameters dot1x port-control (auto|force-authorized| force-unauthorized) auto -> Enables 802. 1x port-based authentication and causes the port to begin in the unauthorized state, allowing only EAPOL frames to be sent and received through the port force-authorized -> Disables 802. 1x port-based authentication and causes the port to transition to the authorized state without any authentication exchange required force-unauthorized -> Causes the port to remain in the unauthorized state, ignoring all attempts by the client to authenticate Command Mode Interface mode No/clear Show Default Description no dot1x port-control show dot1x all / show dot1x interface IFNAME The default is ForceAuthorized Use the dot1x port-control interface configuration command on the switch stack or on a standalone switch to enable manual control of the authorization state of the port. Use the no form of this command to return to the default setting. ASUS(config-if)# dot1x port-control auto Example 17 GigaX2024B/M L2 Managed Switch CLI Manual 6. 4 dot1xradiusserverA. B. C. DRADIUS_KEY [PORTID] Syntax Parameters dot1x radius server A. B. C. D RADIUS_KEY [PORTID] A. B. C. D: RADIUS_KEY: [PORTID]: Command Mode Configure mode No/clear Show Default Description Example This command sets the radius server ip, radius key, and radius port for 802. 1X configuration. ASUS(config)# dot1x radius server 192. 192. 1. 1 testing 1812 show dot1x radius / show running-config IP address RADIUS key RADIUS port 6. 5 dot1x radius secondary-serverA. B. C. D RADIUS_KEY[PORTID] Syntax Parameters dot1x radius secondary-server A. B. C. D RADIUS_KEY [PORTID] A. B. C. D: RADIUS_KEY: [PORTID]: No/clear Show Default Description Example This command sets the secondary radius server ip, radius key, and radius port for 802. 1X configuration. ASUS(config)# dot1x radius secondary-server 192. 192. 1. 2 testing 1812 show dot1x radius / show running-config IP address RADIUS key RADIUS port Command Mode Configure terminal mode 18 GigaX2024B/M L2 Managed Switch CLI Manual 6. 6 Syntax dot1xre-authenticateinterface[IFNAME] dot1x re-authenticate interface [IFNAME] IFNAME: interface's name Parameters No/clear Show Default Description Command Mode Configure terminal mode show dot1x interface IFNAME Use the dot1x reauthenticate privileged EXEC command on the switch stack or on a standalone switch to manually initiate a re-authentication of all 802. 1X-enabled ports or the specified 802. 1X-enabled port. ASUS(config)# dot1x re-authenticate interface fa1/0/1 Example 6. 7 Syntax dot1xreauthentication dot1x reauthentication reauthentication periodic reauthentication of the client Parameters No/clear Show Default Description Command Mode Interface mode no dot1x reauthentication show dot1x all / show dot1x interface IFNAME The dot1x reauthentication feature is default disable Use the dot1x reauthentication interface configuration command on the switch stack or on a standalone switch to enable periodic re-authentication of the client. Use the no form of this command to return to the default setting. [. . . ] D (A. B. C. D|INTERFACE) <1-255> Syntax Parameters ip route A. B. C. D A. B. C. D (A. B. C. D|INTERFACE) <1-255> route A. B. C. D A. B. C. D A. B. C. D INTERFACE <1-255> No/clear Show Default Description Examples This command sets the ip route in this system with distance value for this route. ASUS(config)#ip route 192. 192. 1. 254 255. 255. 255 10 Establish static routes IP destination prefix IP destination prefix mask IP gateway address IP gateway interface name Distance value for this route Command Mode Configure terminal mode no ip route A. B. C. D A. B. C. D (A. B. C. D|INTERFACE) <1-255> show ip route show running-config 206 GigaX2024B/M L2 Managed Switch CLI Manual 18. 4 ip route A. B. C. D/M (A. B. C. D|INTERFACE) Syntax Parameters ip route A. B. C. D/M (A. B. C. D|INTERFACE) route A. B. C. D/M A. B. C. D INTERFACE No/clear Show Establish static routes IP destination prefix (e. g. 10. 0. 0. 0/8) IP gateway address IP gateway interface name Command Mode Configure terminal mode no ip route A. B. C. D/M (A. B. C. D|INTERFACE) show ip route show ip route A. B. C. D/M show running-config Default Description Examples This command sets the ip route in this system ASUS(config)#ip route 192. 192. 1. 254/24 18. 5 ip route A. B. C. D/M (A. B. C. D|INTERFACE) <1-255> Syntax Parameters ip route A. B. C. D/M (A. B. C. D|INTERFACE) <1-255> route A. B. C. D/M A. B. C. D INTERFACE <1-255> No/clear Show Default Description This command sets the ip route in this system with distance 207 Establish static routes IP destination prefix (e. g. 10. 0. 0. 0/8) IP gateway address IP gateway interface name Distance value for this route Command Mode Configure terminal mode no ip route A. B. C. D/M (A. B. C. D|INTERFACE) <1-255> show ip route show running-config GigaX2024B/M L2 Managed Switch CLI Manual value for this route Examples ASUS(config)#ip route 192. 192. 1. 254/24 10 18. 6 show ip route supernets-only Syntax Parameters Command Mode Privileged EXEC mode No/clear Default Description Examples ASUS# show ip route supernets-only show ip route supernets-only 19. [. . . ]