User manual ASUS K1323 P4P800 DELUXE

[. . . ] 0x0008CC00 (9%) A:\>afudos /oMYBIOS03. rom AMI Firmware Update Utility - Version 1. 10 Copyright (C) 2002 American Megatrends, Inc. done A:\> 4-3 User recovery requested. Checking for floppy. . . · · User recovery requested. [. . . ] Select Screen Select Item Change Option General Help Save and Exit Exit +F1 F10 ESC Boot Settings Configuration Quick Boot Full Screen Logo Add On ROM Display Mode Bootup Num-Lock PS/2 Mouse Support Typematic Rate Parity Check Boot to OS/2 Wait for `F1' If Error Hit `DEL' Message Display Interrupt 19 Capture [Enabled] [Enabled] [Force BIOS] [On] [Auto] [Fast] [Disabled] [No] [Enabled] [Enabled] [Disabled] Allows BIOS to skip certain tests while booting. This will decrease the time needed to boot the system. +F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit 4-33 4-34 Security Settings Supervisor Password User Password Change Supervisor Password Boot Sector Virus Protection [Disabled] Not Installed Not Installed <Enter> to change password. <Enter> again to disable password. +F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit 4-35 Security Settings Supervisor Password User Password Change Supervisor Password User Access Level Change User Password Clear User Password Password Check Boot Sector Virus Protection Installed Not Installed [Full Access] [Setup] [Disabled] <Enter> to change password. <Enter> again to disable password. +F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit 4-36 Exit Options Exit & Save Changes Exit & Discard Changes Discard Changes Load Setup Defaults Exit system setup after saving the changes. F10 key can be used for this operation. Select Screen Select Item Enter Go to Sub-screen F1 General Help F10 Save and Exit ESC Exit 4-37 4-38 Chapter 5-1 ® ® ® ® 5-2 5-3 5-4 5-5 5-6 5-7 I 5 . ì5. . î 5-8 5-9 5-10 5-11 5-12 5-13 5-14 ¬ CD ON/OFF PLAY/PAUSE STOP/EJECT PREVIOUS NEXT VOL. UP Esc Esc F1 F1 F2 F2 F3 F3 F4 F4 F5 F5 F6 F6 F7 F7 F8 F8 ¬ CD ON/OFF ¬ CAPS LOCK LED ¬ SCROLL LOCK LED ¬ PLAY/PAUSE STOP/EJECT PREVIOUS VOL. UP ¬¬¬ ¬ ¬ 5-15 5-16 5-17 5-18 5-19 · · · 5-20 5-21 5-22 5-23 5-24 \ \ 5-25 5-26 VIA Tech. RAID BIOS Ver 1. 00 Create Array Delete Array Create/Delete Spare Select Boot Array Serial Number View Create a RAID array with the hard disk attached to VIA IDE controller F1 : , : Enter: ESC : Array Name View Array/Disk Status Move to next item Confirme the selection Exit Mode xxxxx xxxxx Size(GB) xxx. xx xxx. xx Status Hdd Hdd Channel Channel0 Channel0 Channel1 Channel1 Master Slave Master Slave Drive Name XXXXXXXXXX XXXXXXXXXX No Drive No Drive , 5-27 VIA Tech. RAID BIOS Ver 1. 00 Auto Setup For Data Security Array Mode RAID 1 (Mirroring) Select Disk Drives Start Create Process Create a RAID array with the hard disk attached to VIA IDE controller F1 : , : Enter: ESC : Array Name View Array/Disk Status Move to next item Confirm the selection Exit Mode xxxxx xxxxx Size(GB) xxx. xx xxx. xx Status Hdd Hdd Channel Channel0 Channel0 Channel1 Channel1 Master Slave Master Slave Drive Name XXXXXXXXXX XXXXXXXXXX No Drive No Drive RAID RAID RAID RAID 0 for performance 1 for data protection 0/1 SPAN for capacity 5-28 4K 8K 16K 32K 64K The data on the selected disks will be destroyed. Press Y/N RAID RAID RAID RAID RAID 0 for performance 1 for data protection 1 for data protection 0/1 SPAN for capacity Create only Create and duplicate 5-29 The data on the selected disks will be destroyed. Press Y/N RAID RAID RAID RAID 0 for performance 1 for data protection 0/1 SPAN for capacity Create only Create only Create and duplicate 5-30 4K 8K 16K 32K 64K The data on the selected disks will be destroyed. Press Y/N RAID RAID RAID RAID RAID 0 for performance 1 for data protection 0/1 SPAN for capacity SPAN for capacity 5-31 The data on the selected disks will be destroyed. Press Y/N The selected array will be destroyed. Press Y/N The selected drive will be destroyed. Press Y/N 5-32 ESC Channel [ ]Channel0 Master [ ]Channel0 Slave Channel1 Master Channel1 Slave Drive Name XXXXXXXXXX XXXXXXXXXX No Drive No Drive Array Name : Exit Mode xxxxxxx xxxxxxx Size(GB) xxx. xx xxx. xx Status Hdd Hdd VIA Tech. RAID BIOS Ver 1. 00 Create Array Delete Array Create/Delete Spare Select Boot Array Serial Number View Create a RAID array with the hard disk attached to VIA IDE controller F1 : , : Enter: ESC : Array Name View Array/Disk Status Move to next item Confirme the selection Exit Mode xxxxx xxxxx Size(GB) xxx. xx xxx. xx Status Hdd Hdd Channel Channel0 Channel0 Channel1 Channel1 Master Slave Master Slave Drive Name XXXXXXXXXX XXXXXXXXXX No Drive No Drive Serial Number: VJF41646 5-33 \ \ 5-34 Intel(R) Integrated RAID for Serial ATA - RAID Configuration Utility Copyright(C) 2003 Intel Corporation. [. . . ] Non-RAID Disks: Port Drive Model 0 ST320413A 1 ST320413A Serial # xxxxxxxx xxxxxxxx Size 18. 6GB 18. 6GB Status Normal Normal Bootable Yes Yes [ ]-Select [ESC] Exit [Enter]-Select Menu [ RESET ALL DATA RAID DATA ] Resetting all RAID data will remove any internal RAID structures from all RAID disks, including disks with working volumes. These structures are used to maintain the RAID volumes. By removing these structures, the drive will revert back to a Non-RAID disk that can then be used or reallocated to a new RAID volume. [. . . ]