User manual ASUS M2N-VM SE HDMI

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Contents Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Select [CDROM] if you are specifically configuring a CD-ROM drive. Select [ARMD] (ATAPI Removable Media Device) if your device is either a ZIP, LS-120, or MO drive. Configuration options: [Not Installed] [Auto] [CDROM] [ARMD] LBA/Large Mode [Auto] Enables or disables the LBA mode. Setting to [Auto] enables the LBA mode if the device supports this mode, and if the device was not previously formatted with LBA mode disabled. Configuration options: [Disabled] [Auto] Block (Multi-sector Transfer) M [Auto] Enables or disables data multi-sectors transfers. When set to [Auto], the data transfer from and to the device occurs multiple sectors at a time if the device supports multi-sector transfer feature. When set to [Disabled], the data transfer from and to the device occurs one sector at a time. Configuration options: [Disabled] [Auto] ASUS M2N-VM SE HDMI 4-15 PIO Mode [Auto] Selects the PIO mode. Configuration options: [Auto] [0] [1] [2] [3] [4] DMA Mode [Auto] Selects the DMA mode. Configuration options: [Auto] [SWDMA0] [SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5] [UDMA6] SMART Monitoring [Auto] Sets the Smart Monitoring, Analysis, and Reporting Technology. Configuration options: [Auto] [Disabled] [Enabled] 32Bit Data Transfer [Disabled] Enables or disables 32-bit data transfer. Configuration options: [Auto] [Short] [Long] [Longer] [Longest] AI Clock Skew for Channel A [Auto] Configuration options: [Auto] [Normal] [Advance 150ps] [Advance 300ps] . . . [Advance 900] [Delay 150ps] [Delay 300ps]. . . [Delay 900] Current Clock Skew [Normal] Shows the status of the current clock skew. AI Clock Skew for Channel B [Auto] Configuration options: [Auto] [Normal] [Advance 150ps] [Advance 300ps] . . . [Advance 900] [Delay 150ps] [Delay 300ps]. . . [Delay 900] Current Clock Skew [Normal] Shows the status of the current clock skew. The following items appear only when you set the A I O v e r c l o c k i n g item to [Manual]. CPU Frequency [XXX] Allows you to adjust the CPU frequency. The value of this item is auto-detected by the BIOS. Use the < + > and < - > keys to adjust the CPU FSB frequency. You can also type the desired CPU frequency using the numeric keypad. The values range from 200 to 400. 4-20 Chapter 4: BIOS setup PCIE Frequency [XXX] Allows you to adjust the PCIE frequency. The value of this item is auto-detected by the BIOS. Use the < + > and < - > keys to adjust the PCIE FSB frequency. You can also type the desired PCIE frequency using the numeric keypad. The values range from 100 to 150. The following item appears only when you set the A I O v e r c l o c k i n g item to [Ovrerclock Profile]. Overclock Options [Overclock 5%] Allows you to overclock the CPU speed through the available preset values. Configuration options: [Overclock 3%] [Overclock 5%] [Overclock 10%] [Overclock 15%] [Overclock 20%] [Overclock 30%] The following item appears only when you set the A I O v e r c l o c k i n g item to [AI N. O. S. ]. Turbo N. O. S. [Overclock 3%] Configuration options: [Overclock 3%] [Overclock 5%] [Overclock 7%] [Overclock 10%] [Overclock 15%] [Overclock 20%] ASUS M2N-VM SE HDMI 4-21 4. 4. 2 CPU Configuration The items in this menu show the CPU-related information that the BIOS automatically detects. BIOS SETUP UTILITY Advanced CPU Configuration Module Version: 14. 08 Physical Count: 1 Logical Count: 1 AMD Athlon(tm) 64 Processor 3200+ Revision: D0 Cache L1: 128KB Cache L2: 512KB Speed: 2000 MHz Current FSB Multiplier: 10x Maximum FSB Multiplier: 10x Able to Change Freq: Yes uCode Patch Level: 0x4D GART Error Reporting MTRR Mapping Cool `n' Quiet HT Link Speed Memory Configuration v02. 58 (C)Copyright 1985-2005, American Megatrends, Inc. [. . . ] Follow the installation procedures in this section. Requirements · · · · CrossFireTM Edition graphics card (Master) CrossFireTM-ready graphics card (Slave) CrossFireTM-ready motherboard, such as the ASUS M2N-VM SE HDMI motherboard. Make sure that your power supply unit (PSU) can provide at least the minimum power required by your system. Power connectors" on page 2-28 for details. · Visit the ATI website or download the CrossFireTM Xpress 3200 Edition User's Guide from the support CD for detailed hardware requirements and installation procedures. The ATI CrossFireTM technology supports only the following operating systems: - Windows® XP 32-bit (Home or Professional) with Service Pack 2 (SP2) - Windows® XP Professional 64-bit Edition. [. . . ]