User manual ASUS M4N98TD EVO

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Contents Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Pull-In of CHA/B PH1/2 [Disabled] Set this item to [Enabled] to apply enhancement on DRAM Channel A and B, Phase 1 to 2. The number of phases is determined by DRAM frequency and FSB strap. Configuration options: [Disabled] [Enabled] The following ten (10) items are adjusted by typing the desired values using the numeric keypad and press the <Enter> key. You can also use the <+> and <-> keys to adjust the value. To restore the default setting, type [auto] using the keyboard and press the <Enter> key. 3. 4. 13 CPU Voltage [Auto] Allows you to set the CPU VCore voltage. The values range from 0. 85000V to 2. 10000V* with a 0. 00625V interval. ASUS M4N98TD EVO 3-19 · Refer to the CPU documentation before setting the CPU Vcore voltage. Setting a high VCore voltage may damage the CPU permanently, and setting a low VCore voltage may make the system unstable. The value [2. 10000V] of the CPU Voltage item is supported only if the OV_CPU jumper is enabled, otherwise the maximum voltage supported is [1. 70000V]. CPU / Northbridge overvoltage setting on page 2-23 for details. · 3. 4. 14 CPU PLL Voltage [Auto] Allows you to set the CPU PLL voltage. The values range from 1. 50V to 2. 78V with a 0. 02V interval. 3. 4. 15 FSB Termination Voltage [Auto] Allows you to set the front side bus termination voltage. The values range from 1. 20V* to 1. 90V with a 0. 02V interval. The minimum value of this item becomes 1. 10V when a 45nm CPU is installed. 3. 4. 16 DRAM Voltage [Auto] Allows you to set the DRAM voltage. Setting this item to [Disabled] forces the XD feature flag to always return to zero (0). Configuration options: [Disabled] [Enabled] The following items appear only when you set the CPU Ratio Control item to [Auto]. Intel(R) SpeedStep (TM) Tech [Enabled] When set to [Disabled], the CPU runs at its default speed. When set to [Enabled], the CPU speed is controlled by the operating system. Configuration options: [Disabled] [Enabled] Intel(R) C-STATE Tech [Enabled] Allows you enable or disable the Intel® C-STATE Technology. When enabled, the CPU idle is set to C2/C3/C4. Configuration options: [Disabled] [Enabled] ASUS M4N98TD EVO 3-23 3. 5. 2 Chipset The Chipset menu allows you to change the advanced chipset settings. Select an item then press <Enter> to display the sub-menu. BIOSSETUPUTILITY Advanced AdvancedChipsetSettings WARMING:Settingwrongvaluesinbelowsections maycausesystemtomalfunction. North Bridge Configuration Configure North Bridge features. North Bridge Chipset Configuration BIOSSETUPUTILITY Advanced North Bridge Chipset Configuration MemoryRemapFeature [Enabled] PCIMMIOAllocation:4GBTo3328MB MemoryHole [Disabled] InitiateGraphicAdapter [PEG/PCI] ENABLE:Allow remappingof overlappedPCImemory abovethetotal physicalmemory. DISABLE:Donotallow remappingofmemory. Memory Remap Feature [Enabled] Allows you to enable or disable the remapping of the overlapped PCI memory above the total physical memory. Enable this option only when you install 64-bit operating system. Configuration options: [Disabled] [Enabled] Memory Hole [Disabled] Allows you to set the memory hole mode. [. . . ] Visit www. intel. com for more information on the EM64T feature. Visit www. microsoft. com for more information on Windows® 64-bit OS. · · Using the Intel® EM64T feature To use the Intel® EM64T feature: 1. Install a 64-bit operating system (Windows® Vista 64-bit Edition or Windows® XP Professional x64 Edition). Install the 64-bit drivers for the motherboard components and devices from the support DVD. [. . . ]