User manual ASUS M52V

[. . . ] Specifications and information contained in this manual ae furnished for informational use only, and are subject to change at any time without notice, and should not be construed as a commitment by ASUS. ASUS assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual, including the products and software described in it. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Contents Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Remove the metal plate completely. Metal plate bar 3. Use one hand to push the power supply module from inside the power supply cage, then carefully pull out the module from the chassis. ASUS M52V barebone server 2-53 To install a 600 W single power supply module: 1. Firmly hold the power supply module and insert it into the power supply cage. Push the power supply all the way in until its outer end aligns with the rear panel. Be careful with the power supply cables when inserting the power supply module into the cage. Due to space constraints, the cables may get entangled with the installed components or other cables, causing the cables to break! 3. Place the metal plate flat on the outer end of the power supply module, flushed to the top of the chassis, while matching the four hooks with their corresponding holes on the rear panel. Hook matched to a hole 4. Hold the metal plate bar and push it upward to lock the hooks to their holes. At the same time, you may also push the top of the metal plate to fit it completely. Secure the metal plate with the thumb screw. 2-54 Chapter 2: Hardware setup To remove a 600 W dual or redundant power supply: 1. Loosen four screws on the metal brackets that secure the power supply to the chassis. 2. Use one hand to push the power supply module from inside the power supply cage, then carefully pull out the power supply module from the chassis. The drive cage is properly installed when it is parallel to the front panel, and the screw hole matches the hole of the first drive cage. Screw hole 4. Secure the drive cage with a screw. 3-6 Chapter 3: Installation options 3. 3 Upgrading to a dual or redundant power supply Perform this installation if you wish to upgrade your barebone server system from 600 W single power supply to 600 W dual or redundant power supply. Remove the single power supply following the instructions in the section "2. 10 Removable components". Lay the system on its side on a flat surface, then remove the metal stopper screw under the power supply cage. Locate and remove the metal stopper from inside the power supply cage. Keep the metal stopper for later use. 4. Insert the power supply cables and plugs to the power supply cage. ASUS M52V barebone server 3-7 5. Push the power supply halfway to the power supply cage, then attached the a metal bracket on each side of the power supply with two screws. 6. Push the power supply to the power supply cage until the metal brackets and the chassis screw holes align. 7. Secure the power supply to the chassis with two screws on each metal bracket. 3-8 Chapter 3: Installation options 3. 4 Installing a power supply module Perform this installation if you wish to upgrade your barebone server system from 600 W dual to 600 W redundant power supply. Press down the rubber lever of the dummy module to unlock. 2. [. . . ] The User password is required to boot the system preventing unauthorized use. If you forget your password, you can clear it by erasing the CMOS Real Time Clock (RTC) RAM. The RAM data containing the password information is powered by the onboard button cell battery. If you need to erase the CMOS RAM, refer to section "2. 6 Jumpers" for instructions. Password Check [Setup] This field requires you to enter the password before entering the BIOS setup or the system. [. . . ]