User manual ASUS MEW-AML

[. . . ] R MEW-AML Socket 370 Intel® 810 microATX Motherboard USER'S MANUAL USER'S NOTICE No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. [. . . ] Only LINE_OUT will allow you to hear system beeps before the integrated audio has been properly initialized. 18) ATX Power Switch Lead (2-pin PWRSW) The system power is controlled by a momentary switch connected to this lead. Pressing the button once will switch the system between ON and SOFT OFF. Pushing the switch while in the ON mode for more than 4 seconds will turn the system off. The system power LED shows the status of the system's power. 19) IDE Activity LED (2-pin HDLED) This connector supplies power to the cabinet's IDE activity LED. Read and write activity by devices connected to the Primary or Secondary IDE connectors will cause the LED to light up. 20) System Power LED Lead (3-1 pin PLED) This 3-1 pin connector connects the system power LED, which lights when the system is powered ON and turns OFF when it is in standby (suspend) mode. 21) Reset Switch Lead (2-pin RESET) This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch. This is a preferred method of rebooting to prolong the life of the system's power supply. ASUS MEW-AML User's Manual 25 3. HARDWARE SETUP 22) Internal Audio Connector (4-pin CD_IN) (optional) These connectors allow you to receive stereo audio input from such sound sources as a CD-ROM, TV tuner, or MPEG card. CD_IN 1 MEW-AML MEW-AML Internal Audio Connector 23) ATX Power Supply Connector (20-pin block ATXPWR) This connector connects to an ATX power supply. The plug from the power supply will only insert in one orientation because of the different hole sizes. Find the proper orientation and push down firmly making sure that the pins are aligned. IMPORTANT: Make sure that your ATX power supply can supply at least 10mA on the +5-volt standby lead (+5VSB). You may experience difficulty in powering ON your system if your power supply cannot support the load. For WakeOn-LAN support, your ATX power supply must supply at least 720mA +5VSB. 1 MEW-AML +12. 0 Volts +5V Standby Power Good Ground +5. 0 Volts Ground +5. 0 Volts Ground +3. 3 Volts +3. 3 Volts Right Audio Channel Ground Ground Left Audio Channel +5. 0 Volts +5. 0 Volts -5. 0 Volts Ground Ground Ground Power Supply On Ground -12. 0 Volts +3. 3 Volts 3. H/W SETUP Connectors 26 MEW-AML ATX Power Connector ASUS MEW-AML User's Manual 3. HARDWARE SETUP 3. 9 Power Connection Procedures 1. After all connections are made, close the system case cover. Be sure that all switches are OFF (in some systems, marked with ). Connect the power supply cord to the power supply located on the back of your system case according to your system user's manual. Connect the power cord to a power outlet that is equipped with a surge protector. [. . . ] [Auto] returns your computer back to the state it was in before the power failure. Configuration options: [Off] [Auto] [On] 4. BIOS SETUP Power Menu 44 Power-Up Events On External Activity Serial Port [Off] This feature allows your computer to be powered up from Soft-OFF mode when the device connecting to the serial port (such as an external modem) reveives a call. Configuration options: [Off] [On] PCI Bus [Off] This feature allows your computer to be powered up from Soft-OFF mode when a PCI device (such as a modem or network card) receives a call. [. . . ]