User manual ASUS MK241H

[. . . ] · Operate this equipment only from an electrical outlet with the correct power source as indicated on the adapter. · Do not open the cover of this equipment. Opening the cover will void any warranties on the equipment. · Unplug equipment first before cleaning. [. . . ] Also available is the option to enable 802. 1q, a standard to allow multiple bridged networks to transparently share the same physical network link without leakage of information between networks (i. e. Click on the checkbox if you wish to enable this function. ASUS 4-Port Wireless Ethernet Router User Manual Version 1. 0 Document #: BD-AU0014-10 23 After you click on Next, the below screen appears allowing you disable the bridge service if desired. When the settings are complete, the next screen shows a WAN Setup ­ Summary screen displaying the WAN configurations made. ASUS 4-Port Wireless Ethernet Router User Manual Version 1. 0 Document #: BD-AU0014-10 24 Click on the Save button when the settings are correct. The below screen will appear showing the WAN settings that you made. When satisfied with the settings, and no changes are necessary, click on the Finish button. To remove any settings, click on the Remove button. After selecting the Finish button, the below screen will appear. At this point, the router will reboot to save the changes made. ASUS 4-Port Wireless Ethernet Router User Manual Version 1. 0 Document #: BD-AU0014-10 25 LAN Local Area Network (LAN) Setup You can configure the DSL Router IP address and Subnet Mask for the LAN interface to correspond your LAN's IP Subnet. The Save button only saves the LAN configuration data, but does not apply the configurations. Select the Save/Reboot button to save the LAN configuration data and reboot the router and apply the new configurations. NAT If you enable NAT (Network Address Translation), you can configure the Virtual Server, Port Triggering, and DMZ Host. Virtual Servers ASUS 4-Port Wireless Ethernet Router User Manual Version 1. 0 Document #: BD-AU0014-10 26 A virtual server allows you to direct incoming traffic from the WAN side to a specific IP address on the LAN side. Select the virtual server from the drop-down list and complete the server IP address, then click on the Save / Apply button. The following screen appears after you save your selection. To add additional virtual servers, click on the Add button. If you need to remove any of the server names, select the check box and click on the Remove button. ASUS 4-Port Wireless Ethernet Router User Manual Version 1. 0 Document #: BD-AU0014-10 27 Port Triggering Click on the Add button to add Port Triggering to your Internet application. The below screen appears when you click on Add allowing you to select the application that you want to set the port settings for. Enter the username / password for the D-DNS account that you have signed up for and then click on Save / Apply. ADSL There are three major items in the ADSL settings: Modulation Methods Six modulation methods for different linking speed are supported by the 6211 ADSL router: G. Dmt Enabled, G. lite Enabled, T1. 413 Enabled, ADSL Enabled, Annex L Enabled, and ADSL2+ Enabled. Set this value only as directed by your ISP. Phone Line Pair The 6211 ADSL router supports phone lines on pins 2 and 3 or pins 1 and 4 to connect your ADSL line. If your phone system uses pins 2 and 3, attach a normal RJ11 cable to the router and select "Inner pair" on the screen; if your phone system uses pins 1 and 4, attach the phone with the supplied RJ11 cable and select "Outer pair" on the screen. Capability Do not change these settings unless directed by your ISP. ASUS 4-Port Wireless Ethernet Router User Manual Version 1. 0 Document #: BD-AU0014-10 38 DSL Advanced Settings The test mode can be selected from the DSL Advanced Settings page. Test modes are as follows-- · · · · · Normal Reverb Medley No retrain L3 ASUS 4-Port Wireless Ethernet Router User Manual Version 1. 0 Document #: BD-AU0014-10 39 Tone Settings The frequency band of ADSL is split up into 256 separate tones, each spaced 4. 3125 kHz apart. With each tone carrying separate data, the technique operates as if 256 separate modems were running in parallel. The tone range is from 0 to 31 for upstream and from 32 to 255 for downstream. Do not change these settings unless instructed by your ISP. Port Mapping Port mapping is a feature that allows you to open ports to allow certain Internet applications on the WAN side to pass through the firewall and enter your LAN. To use this feature, mapping groups need to be created. To do this, follow the below instructions-- 1. Click on the Add button as displayed below. ASUS 4-Port Wireless Ethernet Router User Manual Version 1. 0 Document #: BD-AU0014-10 40 2. After clicking the Add button, the below configuration screen appears, allowing you enter the groups and the interfaces they are associated with. ASUS 4-Port Wireless Ethernet Router User Manual Version 1. 0 Document #: BD-AU0014-10 41 Wireless This section allows you to configure wireless settings on your router. Basic The below Wireless ­ Basic screen lets you enable or disable wireless. [. . . ] · Beacon Interval--a packet of information that is sent from a connected device to all other devices where it announces its availability and readiness. A beacon interval is a period of time (sent with the beacon) before sending the beacon again. The beacon interval may be adjusted in milliseconds (ms). ASUS 4-Port Wireless Ethernet Router User Manual Version 1. 0 Document #: BD-AU0014-10 46 · Xpress Technology--a technology that utilizes standards based on framebursting to achieve higher throughput. With Xpress Technology enabled, aggregate throughput (the sum of the individual throughput speeds of each client on the network) can improve by up to 25% in 802. 11g only networks and up to 75% in mixed networks comprised of 802. 11g and 802. 11b equipment. [. . . ]