User manual ASUS MS202N

[. . . ] Specifications and information contained in this manual ae furnished for informational use only, and are subject to change at any time without notice, and should not be construed as a commitment by ASUS. ASUS assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual, including the products and software described in it. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Contents Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The ASUS Non-delay Overclocking System feature intelligently determines the system load and automatically boosts the performance for the most demanding tasks. If you install memory module(s) supporting the eXtreme Memory Profile (X. M. P. ) Technology, choose this item to set the profile(s) supported by your memory module(s) for optimizing the system performance. The following sub-item only appears when you set the Ai Overclock Tuner item to [N. O. S]. X. M. P. N. O. S. Mode [Auto] Allows you to set the Non-Delay Overclocking System mode. Configuration options: [Auto] [Standard] [SensitIve] [Heavy Load] 4-18 Chapter 4: BIOS setup Turbo N. O. S. [Overclock 3%] This sub-item appears only when you set the N. O. S. Mode item to either [Standard], [Sensitive], or [Heavy Load]. Allows you to set the maximum overclock percentage for the selected N. O. S. Configuration options: [Overclock 3%] [Overclock 5%] [Overclock 10%] [Overclock 15%] [Overclock 20%] [Overclock 30%] The configuration options for the following sub-item vary depending on the DIMMs you install on the motherboard. eXtreme Memory Profile [Disabled] This item appears only when you set the Ai Overclock Tuner item to [X. M. P. ]. Configuration options: [Disabled] [Profile #1] [Profile #2] 4. 4. 2 CPU Ratio Control [Auto] This item allows you to set the ratio between CPU Core Clock and FSB Frequency. The value is adjusted by typing the desired values using the numeric keypad and press the <Enter> key. Boost Level [1] This sub-item appears only when you set the Transaction Booster item to [Enabled]. Set this item to a higher level to get better performance. Use the <+> and <-> keys to adjust the value. The values range from 1 to 8. The following seven items on the next page appear only when you set the Ai Overclock Tuner item to [Manual] and [X. M. P. ] and are adjusted by typing the desired values using the numeric keypad and press the <Enter> key. Use the <+> and <-> keys to adjust the value. To restore the default setting, type [auto] using the keyboard and press the <Enter> key. 4. 4. 12 CPU Voltage [Auto] Allows you to set the CPU VCore voltage. The values range from 0. 85000V to 1. 70000V with a 0. 00625V interval. Refer to the CPU documentation before setting the CPU Vcore voltage. Setting a high VCore voltage may damage the CPU permanently, and setting a low VCore voltage may make the system unstable. 4. 4. 13 CPU PLL Voltage [Auto] Allows you to set the CPU PLL voltage. The values range from 1. 00V to 2. 30V with a 0. 02V interval. 4. 4. 14 FSB Termination Voltage [Auto] Allows you to set the front side bus termination voltage. The values range from 1. 20V to 1. 50V with a 0. 02V interval. 4. 4. 15 DRAM Voltage [Auto] Allows you to set the DRAM voltage. The values range from 1. 80V to 3. 00V with a 0. 02V interval. 4. 4. 16 North Bridge Voltage [Auto] Allows you to set the North Bridge voltage. [. . . ] Click the Power button on the Monitor power section to open the Power Options Properties window. 8. On the Power schemes section, click , then select any option except Home/Office Desktop or Always On. Click Apply, then click OK. 9. 10. After you adjust the power scheme, the CPU internal frequency slightly decreases when the CPU loading is low. The screen displays and procedures may vary depending on the operating system. ASUS MS202N A-3 A. 3 Intel® Hyper-Threading Technology · · The motherboard supports Intel® Pentium® LGA775 processors with Hyper-Threading Technology. Hyper-Threading Technology is supported under Windows® Vista/XP and Linux 2. 4. x (kernel) and later versions only. [. . . ]