User manual ASUS MY CINEMA-PE6100ANALOG MY CINEMA SERIES USER’S MANUAL(ENGLISH)

[. . . ] SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. Offer to Provide Source Code of Certain Software This product may contain copyrighted software that is licensed under the General Public License (“GPL”) and under the Lesser General Public License Version (“LGPL”). [. . . ] The Serial ATA RAID feature (RAID 0, 1, 5, and 10) is available only if you are using Windows® XP SP3 or later version. • When using hot-plug and NCQ, set the SATA Mode Selection item in the BIOS to [AHCI]. See section 2. 5. 3 SATA Configuration for details. 11. This connector is for the additional USB 3. 0 ports. Connect the USB 3. 0 bracket cable to this connector, then install the USB 3. 0 bracket to the rear side of the chassis. If your chassis support customized front panel installation, with ASUS USB 3. 0 header, you can have a front panel USB 3. 0 solution. USB3_34 USB 3. 0 connector (20-1 pin USB3_34) MY CINEMA-PE6100ANALOG MY CINEMA-PE6100ANALOG USB3. 0 front panel connector • The USB 3. 0 module is purchased separately. • Due to Intel® limitations, the USB3_34 only supports Windows® 7 operating system. ASUS MY CINEMA-PE6100ANALOG 1-29 1. 11 Onboard switches Onboard switches allow you to fine-tune performance when working on a bare or open-case system. This is ideal for overclockers and gamers who continually change settings to enhance system performance. MemOK!switch Installing DIMMs that are incompatible with the motherboard may cause system boot failure, and the DRAM_LED near the MemOK!switch until the DRAM_LED starts blinking to begin automatic memory compatibility tuning for successful boot. MY CINEMA-PE6100ANALOG MY CINEMA-PE6100ANALOG MemOK!switch • Refer to section 1. 12 Onboard LEDs for the exact location of the DRAM_LED. • The DRAM_LED also lights when the DIMM is not properly installed. • Ensure that you install Windows® XP Service Pack 3 / Windows® 7 or later versions before installing the drivers for better compatibility and system stability. 1. 13. 2 The Support DVD that comes with the motherboard package contains the drivers, software applications, and utilities that you can install to avail all motherboard features. The contents of the Support DVD are subject to change at any time without notice. Visit the ASUS website at www. asus. com for updates. Support DVD information To run the Support DVD Place the Support DVD to the optical drive. If Autorun is enabled in your computer, the DVD automatically displays the Specials screen. Click Drivers, Utilities, Manual, Contact, and Specials tabs to display their respective menus. The following screen is for reference only. Click an icon to display Support DVD/ motherboard information Click an item to install If Autorun is NOT enabled in your computer, browse the contents of the Support DVD to locate the file ASSETUP. EXE from the BIN folder. Double-click the ASSETUP. EXE to run the DVD. 1-32 Chapter 1: Product introduction Chapter 2 BIOS information 2. 1 Managing and updating your BIOS Save a copy of the original motherboard BIOS file to a USB flash disk in case you need to restore the BIOS in the future. Copy the original motherboard BIOS using the ASUS Update utility. 2. 1. 1 The ASUS Update is a utility that allows you to manage, save, and update the motherboard BIOS in Windows® environment. • ASUS Update requires an Internet connection either through a network or an Internet Service Provider (ISP). • This utility is available in the support DVD that comes with the motherboard package. ASUS Update utility Installing ASUS Update To install ASUS Update: 1. 2. 3. Place the support DVD in the optical drive. Click the Utilities tab, then click AI Suite II. Follow the onscreen instructions to complete the installation. Quit all Windows® applications before you update the BIOS using this utility. Updating the BIOS To update the BIOS: 1. 2. From the Windows® desktop, click Start > Programs > ASUS > AI Suite II > AI Suite II X. XX. XX to launch the AI Suite II utility. Click Update button from the Quick Bar, and then click ASUS Update from the popup menu. [. . . ] Consult the dealer or an experienced radio/TV technician for help. The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. IC: Canadian Compliance Statement Complies with the Canadian ICES-003 Class B specifications. This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations. [. . . ]