User manual ASUS MY CINEMA-U3000MINI

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. [. . . ] Do not place jumper caps on the fan connectors!The CPU_FAN connector supports a CPU fan of maximum 2A (24 W) fan power. 5. These connectors are for USB 2. 0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2. 0 specification that supports up to 480 Mbps connection speed. USB connectors (10-1 pin USB78, USB910) USB910 USB+5V USB_P10USB_P10+ GND NC CPU FAN PWM CPU FAN IN CPU FAN PWR GND GND +12V Rotation USB78 USB+5V USB_P8USB_P8+ GND NC USB+5V USB_P7USB_P7+ GND PIN 1 MY CINEMA-U3000MINI MY CINEMA-U3000MINI USB2. 0 connectors Never connect a 1394 cable to the USB connectors. The USB module cable is purchased separately. Chapter 1: Product introduction USB+5V USB_P9USB_P9+ GND PIN 1 1-23 6. These connectors connect to Serial ATA 3. 0 Gb/s hard disk drives and optical drives via Serial ATA 3. 0 Gb/s signal cables. SATA3G_1 GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXN1 RSATA_RXP1 GND Intel® H61 Serial ATA 3. 0Gb/s connectors (7-pin SATA3G_1~4) SATA3G_3 GND RSATA_RXP3 RSATA_RXN3 GND RSATA_TXN3 RSATA_TXP3 GND SATA3G_2 GND RSATA_TXP2 RSATA_TXN2 GND RSATA_RXN2 RSATA_RXP2 GND SATA3G_4 GND RSATA_RXP4 RSATA_RXN4 GND RSATA_TXN4 RSATA_TXP4 GND MY CINEMA-U3000MINI MY CINEMA-U3000MINI SATA connectors • You must install Windows® XP Service Pack 3 or a later version before using Serial ATA hard disk drives. • Due to H61 Chipset limitation, AHCI Mode only works on Windows® Vista / Windows® 7. Under Windows® XP, there is no need to change the SATA type. • To configure the SATA type in BIOS, click Advanced Mode > Advanced tab > SATA Configuration > SATA Mode Selection. • When using hot-plug and NCQ on Windows® Vista / Windows® 7, set the SATA Mode item in the BIOS to [AHCI Mode]. See section 2. 5. 4 SATA Configuration for details. 7. This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port. Connect the S/PDIF Out module cable to this connector, then install the module to a slot opening at the back of the system chassis. Digital audio connector (4-1 pin SPDIF_OUT) MY CINEMA-U3000MINI SPDIF_OUT MY CINEMA-U3000MINI Digital audio connector The S/PDIF module is purchased separately. 1-24 SPDIFOUT GND +5V ASUS MY CINEMA-U3000MINI 8. This connector supports several chassis-mounted functions. PWR LED PWR BTN System panel connector (10-1 pin PANEL) F_PANEL MY CINEMA-U3000MINI HD_LED MY CINEMA-U3000MINI System panel connector • This 2-pin connector is for the system power LED. The AI Suite II Quick Bar appears. Click Update button from the Quick Bar, and then click ASUS Update from the popup menu. From the list, select either of the following methods: Updating from the Internet a. Select Update BIOS from the Internet, then click Next. b. Select the ASUS FTP site nearest you to avoid network traffic, then click Next. c. From the FTP site, select the BIOS version that you wish to download then click Next. Chapter 2: BIOS information 2-1 The ASUS Update utility is capable of updating itself through the Internet. Always update the utility to avail all its features. a. Select Update BIOS from file, then click Next. Locate the BIOS file from the Open window, then click Open. Follow the onscreen instructions to complete the updating process. 2. 1. 2 The ASUS EZ Flash 2 feature allows you to update the BIOS without using an OS‑based utility. Before you start using this utility, download the latest BIOS file from the ASUS website at www. asus. com. ASUS EZ Flash 2 To update the BIOS using EZ Flash 2: 1. 2. Enter the Advanced Mode of the BIOS setup program. Go to the Tool menu to select ASUS EZ Flash Utility and press <Enter> to enable it. Insert the USB flash disk that contains the latest BIOS file to the USB port. 2-2 ASUS MY CINEMA-U3000MINI 3. 4. 5. 6. Press the Up/Down arrow keys to find the USB flash disk that contains the latest BIOS, and then press <Enter>. [. . . ] • • • Increase the separation between the equipment and receiver. This device must accept any interference received including interference that may cause undesired operation. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. IC: Canadian Compliance Statement Complies with the Canadian ICES-003 Class B specifications. This device complies with RSS 210 of Industry Canada. [. . . ]