User manual ASUS P1-P5945GC

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners benefit, without intent to infringe. ii Table of contents Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The pie chart at the bottom of the window represents the used (blue) and the available HDD space. 3-10 Chapter 3: Starting up Memory usage The Memory tab shows both used and available physical memory. The pie chart at the bottom of the window represents the used (blue) and the available physical memory. Configuring PC Probe II Click to view and adjust the sensor threshold values. The Config window has two tabs: Sensor/Threshold and Preference. The Sensor/Threshold tab enables you to activate the sensors or to adjust the sensor threshold values. The Preference tab allows you to customize sensor alerts, change temperature scale, or enable the Q-Fan feature. * Loads the default threshold values for each sensor Applies your changes *Available on some motherboards only. Cancels or ignores your changes Loads your saved configuration Saves your configuration ASUS Pundit P1-P5945GC 3-11 3. 4. 2 DTS function Refer to the appendix of this section on page 3-15 for more information about DTS function. DTS Connect is embedded in the audio drivers. After the driver installed, there is "Realtek HD Audio Manager" icon in the desktop manual bar (see figure below). When click the icon or insert the device into the phone jack, the manager will poop out. You can click the dts Neo: PC and dts Interactive buttons to initiate those functions a shown below. DTS NEO: PC "DTS CONNECT", "DTS INTERACTIVE" and "DTS NEO: PC" are trademark of DTS, Inc. "DTS" is a registered trademark of DTS, Inc. 3-12 Chapter 3: Starting up DTS Interactive When DTS Interactive is enabled, only digital audio output(S/ PDIF) is working, and you will not hear sound from analog speaker or headphone. "DTS CONNECT", "DTS INTERACTIVE" and "DTS NEO: PC" are trademark of DTS, Inc. "DTS" is a registered trademark of DTS, Inc. ASUS Pundit P1-P5945GC 3-13 Detailed Settings "DTS CONNECT", "DTS INTERACTIVE" and "DTS NEO: PC" are trademark of DTS, Inc. Set to +5VSB to wake up from S3 and S4 sleep modes (no power to CPU, DRAM in slow refresh, power supply in reduced power mode). 12 USBPW56 23 +5V(Default) 12 R +5VSB 23 USBPW34 +5V (Default) 21 +5VSB USBPW12 USB device Wake up · +5V(Default) +5VSB The USB device wake-up feature requires a power supply that can provide 500mA on the +5VSB lead for each USB port; otherwise, the system would not power up. The total current consumed must NOT exceed the power supply capability (+5VSB) whether under normal condition or in sleep mode. · 4-4 Chapter 4: Motherboard info 32 4. 4 1. Connectors Serial ATA connectors (7-pin SATA1, SATA2) These connectors are for the Serial ATA signal cables for Serial ATA hard disk drives. Important notes on Serial ATA · · Only Windows® 2000 Service Pack 4 / Windows® XP Service Pack1 and above support Serial ATA hard disk drives. When using the connectors in Standard IDE mode, connect the primary (boot) hard disk drive to the SATA1 or SATA2 connector. SATA1 R SATA2 GND RSATA_RXN2 RSATA_RXP2 GND RSATA_TXN2 RSATA_TXP2 GND GND RSATA_RXN1 RSATA_RXP1 GND RSATA_TXN1 RSATA_TXP1 GND SATA Connectors 2. COM port connector (10-1pin COM1) This connector is for a serial (COM) port. Connect the serial port module cable to this connector, then install the module to a slot opening at the back of the system chassis. COM1 R PIN 1 COM Port Connector ASUS Pundit P1-P5945GC 4-5 3 IDE connectors (40-1 pin PRI_IDE) The onboard IDE connectors are for Ultra DMA 133/100/66 signal cable(s). There are three connectors on each Ultra DMA 133/100/66 signal cable: blue, black, and gray. Connect the blue connector to the motherboards IDE connector, then select one of the following modes to configure your device(s). R IDE Connector Drive jumper setting Single device Two devices Cable-Select or Master Cable-Select Master Slave Mode Cable of device(s) Master Slave Master Slave Cable connector Black Black Gray Black or gray · Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable. Use the 80-conductor IDE cable for Ultra DMA 133/100/66 IDE devices. · If any device jumper is set as "Cable-Select", make sure all other device jumpers have the same setting. 4-6 Chapter 4: Motherboard info PRI_IDE 4. CPU Fan connectors (3-pin CPU_FAN) The fan connectors support cooling fans of 350 mA~740 mA (8. 88 W max. ) or a total of 1 A~2. 22 A (26. 64 W max. ) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. R CPU Fan Connector Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. [. . . ] Configuration options: [250] [500] [750] [1000] OS Select for DRAM > 64MB [Non-OS2] Set this item to OS2 only when you are running on an OS/2 operating system with an installed RAM of greater than 64 KB. Configuration options: [Non-OS2] [OS2] Full Screen LOGO [Enabled] Allows you to enable or disable the full screen logo display feature. Configuration options: [Disabled] [Enabled] Make sure that the above item is set to [Enabled] if you want to use the ASUS MyLogo3TM feature. Halt On [All, But Keyboard] Allows you to error report type. Configuration options: [All Errors] [No Errors] [All, But Keyboard] [All, But Diskette] [All, But Disk/Key] 5. 6. 4 Security Phoenix-Award BIOS CMOS Setup Utility Boot Security Select Menu Clear Clear [Setup] Item Specific Help Supervisor Password User Password Password Check Supervisor Password User Password To set a password: 1. [. . . ]