User manual ASUS P2-P5N9300 P2-P5N9300/P4-P5N9300 DISPLAY SETTING(ENGLISH)

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Table of contents Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The pie chart at the bottom of the window represents the used (blue) and the available HDD space. 3-10 Chapter 3: Starting up Memory usage The Memory tab shows both used and available physical memory. The pie chart at the bottom of the window represents the used (blue) and the available physical memory. Configuring PC Probe II Click to view and adjust the sensor threshold values. The Config window has two tabs: Sensor/Threshold and Preference. The Sensor/Threshold tab enables you to activate the sensors or to adjust the sensor threshold values. The Preference tab allows you to customize sensor alerts, change temperature scale, or enable the Q-Fan feature. Loads the default threshold values for each sensor Applies your changes Cancels or ignores your changes Loads your saved configuration Saves your configuration ASUS P1-P5945G/P2-P5N9300 3-11 Chapter 4 ASUS P1-P5945G/P2-P5N9300 Motherboard info This chapter gives information about the motherboard that comes with the system. This chapter includes the motherboard layout, jumper settings, and connector locations. The Pundit P1-P5945G/P2-P5N9300 barebone system comes with an ASUS motherboard. This chapter provides technical information about the motherboard for future upgrades or system reconfiguration. SB_PWR SATA1 MS_CON 4Mb BIOS USB7 Super I/O BUZZER PRI_IDE Intel ICH7 VIA VT6308P RTS5111 R Motherboard layout USBPW12 KBPWR EATXPWR PCI1 CPU_ FAN PS/2KBMS T Mouse : B: Keyboard Introduction LAN_USB12 Realtek RTL8111B USBPW34 USB34 Intel MCH945G COM1 LG 75 A7 PWRSW IE1394_2 VGA_DVI USB56 CD ADI AD1988B DDR2 DIMM_A1(64 bit, 240-pin module) SPDIF_OUT FP_AUDIO DDR2 DIMM_B1(64 bit, 240-pin module) BACK_AUDIO ATX12V 4. 1 4. 2 33. 0cm(13in) 26. 4cm(10. 4in) Cypress CY28551 CF_CON SD_CON RSTCON CR2032 3V Lithium Cell CMOS Power PANEL 4-2 Chapter 4: Motherboard info USBPW78 CLRTC 4. 3 1. Jumpers Clear RTC RAM (CLRTC) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in the CMOS, which includes the system setup information such as system passwords. Turn OFF the computer and unplug the power cord. Move the jumper cap from pins 1-2 (default) to pins 2-3. The system may become unstable or may not boot up if the power is inadequate. Make sure that your power supply unit (PSU) can provide at least the minimum power required by your system. · 6. Internal audio connectors (4-pin CD) These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, TV tuner, or MPEG card. CD (black) R ATX Power Connector Enable the CD-IN function in the audio utility when using this connector. 4-8 Chapter 4: Motherboard info Right Audio Channel Ground Ground Left Audio Channel +3 Volts -12 Volts Ground PSON# Ground Ground Ground -5 Volts +5 Volts +5 Volts +5 Volts Ground ATX12V GND +12V DC 7. Back audio connector (20-1 pin Back_Audio Connector) BACK_AUDIO SENSE FRONT BCAZ FRONTR BCAZ FRONT L SENSE LIN1 BCAZ LIN1 R BCAZ LIN1 L SENSE MIC1 BCAZ MIC1R BCAZ MIC1L R Back_Audio Connector We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard's high-definition audio capability. 8. Digital audio connector (4-1 pin SPDIF_OUT) This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port(s). Connect the S/PDIF module cable to this connector, then install the module to a slot opening at the back of the system chassis. R Digital Audio Connector SPDIF_OUT module SPDIF_OUT The S/PDIF module is purchased separately. ASUS P1-P5945G/P2-P5N9300 +5V SPDIFOUT GND AGND_A SENSE SUR BCAZ SUR R BCAZ SUR L SENSE SURB BCAZ SURBR BCAZ SURBL SENSE CN1 BCAZ LEF R BCAZ CEN L 4-9 9. System panel connector (6 pin PANEL) This connector supports several chassis-mounted functions. PA NEL HD_LEDR System Panel Connector The system panel connector is color-coded for easy connection. Refer to the connector description below for details. · System power LED (2-pin PLED) This 3-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode. Hard disk drive activity (2-pin HDLED) This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED cable to this connector. The IDE LED lights up or flashes when data is read from or written to the HDD. Power/Soft-off button (2-pin PWRSW) This connector is for the system power button. Pressing the power button turns the system ON or puts the system in SLEEP or SOFT-OFF mode depending on the BIOS settings. [. . . ] Confirm the password when prompted. Select Screen Select Item +Change Option F1 General Help F10 Save and Exit password. The Supervisor ESC Exit The message "Password Installed" appears after you successfully set your password. To change the supervisor password, follow the same steps as in setting a user password. To clear the supervisor password, select the Change Supervisor Password then press <Enter>. [. . . ]