User manual ASUS P200

[. . . ] ® AP200 Dual Pentium® III Group Server Hardware Reference Guide User's Notice No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. [. . . ] Before picking it up again, touch the antistatic bag and the metal frame of the system unit at the same time. · Handle the devices carefully in order to prevent permanent damage. AP200 Hardware Reference Guide I. Unpack your server, but do not connect the power cord. IMPORTANT Most servers use an AT power supply that has a fixed On and Off switch located on the front. This server uses an ATX power supply that is normally off until an electrical signal is given to the power supply through a momentary switch located on the front of the server. There is always a standby power in the power supply for ATX power supply features to work. Therefore removing the power cord is necessary to prevent electrical shocks when working on the server components. This server is equipped with a lockable panel to prevent unauthorized access. Install final server components such as CPU, memory, hard disk drives, and expansion cards. Use this hardware reference guide along with your motherboard's User's Manual in order to complete the installations. Connect a keyboard and a mouse (purchased separately). Connect a VGA-compatible monitor (purchased separately). Connect a printer to the parallel port if desired. (An optional network card is needed. ) 8. Set the power supply input voltage to either 115V for 110V-120V areas or 230V for 220V-240V areas. CAUTION The voltage must be set correctly or damage may occur. Connect the included power cord to the server's power supply. Connect the server to a grounded (three pronged) AC power source such as a UPS or power strip (preferably with surge protection). WARNING This server is designed for connection to a grounded (earthed) outlet. To reduce the risk of electrical shock or damage to your server, do not bypass the grounding plug. AP200 Hardware Reference Guide 11 I. Top Panel LED Status Indicator CD-ROM Drive 5. 25" Device Bays ATX Power Button Floppy Disk Drive Reset Button Infrared Window (Reserved) Left Panel Chassis Stabilizers 12 AP200 Hardware Reference Guide B C D E F G H Front View I J II. Components Rear View A B C D E F G H I J K L M N O II. [. . . ] Cable Limits 1) 12m (29. 4ft) 2) 3m - 1. 5m 3) 3m (9. 8ft) 4) 3m - 1. 5m 5) 3m (9. 8ft) Max Data Transfer Rates Max Devices Ultra2-SCSI (68-pin 80MB/Sec) 15 Wide Ultra-SCSI (68-pin 40MB/Sec) 4-7 Wide-SCSI (68-pin 20MB/Sec) 15 Narrow Ultra-SCSI (50-pin 20MB/Sec) 4-7 Narrow Fast-SCSI (50-pin 10MB/Sec) 7 IMPORTANT · The SCSI ID for devices on one connector cannot be the same as the SCSI ID for devices on the other connectors. None of the devices on any connector can use ID7, which is reserved for the SCSI controller. · A maximum of 15 devices may be connected to the motherboard (three connectors) at one time. The following "Max Devices" are for individual connectors and do not take into account other SCSI devices. [. . . ]