User manual ASUS P4BP-MX 2.0

[. . . ] P4BP-MX 2. 0 User Guide Motherboard E1648 Checklist First Edition June 2004 Copyright © 2004 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] Infrared connector (10-pin IR_CON) These connectors support an optional wireless transmitting and receiving infrared module. The module mounts to a small opening on the system chassis that supports this feature. You must also configure the UART2 Use As parameter in BIOS to set UART2 for use with IR. Use the ten pins as shown in Back View and connect a ribbon cable from the module to the motherboard IR connector according to the pin definitions. IR_CON PX GND IRRX +5V P4BP-MX 2. 0 P4BP-MX 2. 0 Infrared Module Connector The IR module is purchased separately. 12. Serial connector (9-pin COM2 ) This 9-pin connector connects to a COM2 bracket. Connect the COM2 cable to this connector and install the bracket on an available slot in the rear panel of the chassis. PIN 1 COM2 P4BP-MX 2. 0 P4BP-MX 2. 0 Serial COM2 Bracket The COM2 bracket is purchased separately. ASUS P4BP-MX 2. 0 motherboard 1-21 13. System panel connector (10-1 pin PANEL) This connector accommodates several system front panel functions. Power LED Power Button F_PANEL P4BP-MX 2. 0 IDE_LED P4BP-MX 2. 0 System Panel connector · System Power LED Lead (2-pin PLED) This 2-pin connector connects to the system power LED. The LED lights up when you turn on the system power. · ATX Power Switch / Soft-Off Switch Lead (2-pin PWR) This connector connects a switch that controls the system power. Pressing the power switch turns the system between ON and SLEEP, or ON and SOFT OFF, depending on the BIOS or OS settings. Pressing the power switch while in the ON mode for more than 4 seconds turns the system OFF. · Reset Switch (2-pin RESET) This 2-pin connector connects to the case-mounted reset switch for rebooting the system without turning off the power switch. · Hard Disk Activity Lead (Red 2-pin IDE_LED) This connector supplies power to the hard disk activity LED. The read or write activities of any device connected to the primary or secondary IDE connector cause this LED to light up. 1-22 Chapter 1: Product introduction IDE_LED+ IDE_LEDGround Reset NC PLED+ PLEDPWR GND Reset Chapter 2 This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided. BIOS information ASUS P4BP-MX 2. 0 motherboard 2-1 2. 1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. AwardBIOS Flash Utility (EZ Flash feature that updates the BIOS using a floppy disk during POST. ) 2. ASUS CrashFree BIOS (Updates the BIOS using a bootable floppy disk when the BIOS gets corrupted. ) 3. ASUS Update (Updates the BIOS in Windows® environment. ) Refer to the corresponding section for details on these utilities. Important notes · It is recommended that you save a copy of the original motherboard BIOS file to a bootable floppy disk in case you need to restore the BIOS in the future. Copy the original motherboard BIOS using the ASUS Update or AFLASH utilities. A working BIOS file for this motherboard is in the support CD. Use this file only when you do not have a copy of the original motherboard BIOS file in a floppy disk. Visit the ASUS website and download the latest BIOS file for this motherboard using the ASUS Update utility. · · 2. 1. 1 Creating a bootable floppy disk 1. Do either one of the following to create a bootable floppy disk. DOS environment Insert a 1. 44 MB floppy disk into the drive. At the DOS prompt, type: format A:/S then press <Enter>. [. . . ] Select Save & Exit or make other changes before saving the values to the non-volatile RAM. 2-24 Chapter 2: BIOS information Chapter 3 This chapter describes the contents of the support CD that comes with the motherboard package. Software support 3. 1 Install an operating system This motherboard supports Windows® 98SE/ME/2000/XP operating system (OS). Always install the latest OS version and corresponding updates to maximize the features of your hardware. Motherboard settings and hardware options vary, so use the setup procedures presented in this chapter for general reference only. Refer to your OS documentation for more information. 3. 2 Support CD information The support CD that came with the motherboard contains useful software and several utility drivers that enhance the motherboard features. The contents of the support CD are subject to change at any time without notice. Visit the ASUS website for updates. 3. 2. 1 Running the support CD To begin using the support CD, simply insert the CD into your CD-ROM drive. [. . . ]