User manual ASUS P4R800-VM

[. . . ] P4R800-VM User Guide Motherboard E1662 Checklist Revised Edition V4 May 2004 Copyright © 2004 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] CPU and chassis fan connectors (3-pin CPU_FAN1, CHA_FAN1) The fan connectors support cooling fans of 350mA~740mA (8. 88W max. ) or a total of 1A~2. 22A (26. 64W max. ) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors. Lack of sufficient air flow within the system may damage the motherboard components. DO NOT place jumper caps on the fan connectors! CPU_FAN1 Rotation +12V GND P4R800-VM CHA_FAN1 Rotation +12V GND P4R800-VM 12-Volt Fan Connectors 1-20 Chapter 1: Product introduction 7. Speaker out connector (4-pin SPEAK1) This connector connects to the case-mounted speaker and allows you to hear system beeps and warnings. SPEAK1 P4R800-VM 1 P4R800-VM Speaker Out Connector 8. USB header (10-1 pin USB56) If the USB ports on the rear panel are inadequate, a USB header is available for additional USB ports. Connect the USB cable of an optional USB 2. 0 module to this header. You may install the USB module in the chassis front panel. The module has two USB 2. 0 ports for connecting next generation USB peripherals such as high resolution cameras, scanners, and printers. +5V GND GND Speak Out P4R800-VM USB56 USB+5V USB_P5USB_P5+ GND 1 P4R800-VM USB 2. 0 Header The USB module is purchased separately. ASUS P4R800-VM motherboard user guide USB+5V USB_P6USB_P6+ GND NC 1-21 9. Front panel audio connector (10-1 pin FP_AUDIO1) This is an interface for the front panel cable that allows convenient connection and control of audio devices. Be default, the pins labeled LINE OUT_R/BLINE_OUT_R and the pins LINE OUT_L/BLINE_OUT_L are shorted with jumper caps. Remove the caps only when you are connecting the front panel audio cable. AGND +5VA BLINE_OUT_R P4R800-VM FP_AUDIO1 MIC2 MICPWR Line out_R NC Line out_L P4R800-VM Front Panel Audio Connector 10. Serial port connector (10-1 pin COM1) This green connector accommodates the bundled serial port module. Install the module into a slot opening at the back of the system chassis, then insert the module's green cable plug to this connector. COM1 P4R800-VM PIN 1 P4R800-VM Serial Port Connector 1-22 Chapter 1: Product introduction BLINE_OUT_L 11. Power LED Lead (3-1 pin PLED1) This 3-1 pin connector is for the system power LED. Connect the 3-pin power LED cable from the system chassis to this connector. The LED lights up when you turn on the system power, and blinks when the system is in sleep mode. The power LED lead (PLED1) is present only on PCB versions 1. 03 or later. P4R800-VM PLED1 1 PLED+ NC PLEDPower LED P4R800-VM PLED Setting 12. System panel connector (10-1 pin F_PANEL1) This connector accommodates several chassis-mounted functions. Power Switch P4R800-VM F_PANEL1 IDE LED+ IDE LEDGround Reset P4R800-VM F_Panel Connector IDE_LED · Power LED (2-pin PWR_LED) This connector is for the system power LED. The LED lights up when you turn on the system power, and blinks when the system is in sleep mode. If your motherboard package comes with a 2-pin to 3-pin power LED converter, connect the 2-pin plug to this connector, and the other end to the 3-pin power LED plug from the system chassis. ASUS P4R800-VM motherboard user guide Power LED+ Power LEDPower Switch Ground Reset Switch 1-23 · Power Button/Soft-Off Button (2-pin PWR_BTN) This connector is for the system power button that controls the system power. Pressing the power button turns the system ON or puts the system to SLEEP or SOFT OFF mode, depending on the BIOS or OS settings. Pressing the power button more than 4 seconds while the system is ON turns the system OFF. · IDE LED (2-pin IDE_LED) This connector supplies power to the hard disk drive activity LED. [. . . ] F10 key can be used for this operation. Pressing <Esc> does not immediately exit this menu. Select one of the options from this menu or <F10> from the legend bar to exit. Exit & Save Changes Once you are finished making your selections, choose this option from the Exit menu to ensure the values you selected are saved to the CMOS RAM. The CMOS RAM is sustained by an onboard backup battery and stays on even when the system is turned off. When you select this option, a confirmation window appears. [. . . ]