User manual ASUS P5000

[. . . ] R AP5000 Dual Pentium® II Server Platform Installation Guide USER'S NOTICE No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. [. . . ] INTRODUCTION Preface 7 Preface ASUS AP5000 Installation Guide I. INTRODUCTION (This page was intentionally left blank) I. INTRODUCTION 8 ASUS AP5000 Installation Guide II. BARE-BONE KITS Bare-Bone Kits Overview This section will show you the component kits of AP5000 including housing, motherboard, CPU card, device drive-bay, back plane board, and slot card. The housing of the AP5000 is ivory white. Its front and back view after system assembly is shown below: Power button Front door Device drive-bay Key locker of front door Cover install/ remove locker Tower feet with wheel Fig 2-1: Front view of housing Redundant power supply Power connectors Parallel I/O port Serial I/O port Fig 2-2: Back side of housing ASUS AP5000 Installation Guide 9 II. BARE-BONE KITS MOTHERBOARD The AP5000 uses the P2L97-DS motherboard which is designed to support dual Pentium II processors. For detailed specifications, refer to the P2L97DS user's manual. II. BARE-BONE KITS 10 SEC CPU Slots PS/2 Mouse (Top) PS/2 K'Board (Bottom) USB Port 1 (Top) USB Port 2 (Bottom) Intel 440LX AGPset DIMM Sockets Parallel (Top) Primary/Secondary IDE Connectors Narrow/Wide SCSI Connectors (optional) Adaptec's 7880 Fast/Wide SCSI Chipset (optional) Accelerated Graphics Port 4 PCI Slots Multi-I/O Chip Hardware Monitor (optional) 2 ISA Slots Intel PIIX4 PCIset Programmable 2Mbit Flash ROM Floppy Disk Drive Connector Fig 2-3: P2L97-DS Layout ASUS AP5000 Installation Guide II. BARE-BONE KITS DRIVE BAY There are two types of drive bays, that could mount, floppy drive, CDROM drive and hard disk drive. One type is fixed type and another is removable type which has key-lock feature, refer to the following figures: Fig 2-4: Fixed type drive bay Fig 2-5: Hot-Swap drive bay BACK PLANE BOARD The ASUS Back Plane Board, DA-BP4 series, were designed for carrying four removable SCSI devices per Back Plane Board. Normally those removable SCSI drives are installed on the Hot-Swap Drive Bay with a small slot card connected together (Fig 2-7). When the completed drive set plugs in, the slot board of drive Bay and bus of DA-BP4 will be connected together. After that, all the four SCSI-ID of SCSI devices could be managed from the switches of Back Plane Board (Fig 2-6). Moreover there are two models of Back Plane Boards available for none SAF-TE and SAF-TE which are named DA-BP4-1 and DA-BP4-1S. SAF-TE one mounted one more management chip named GEM200RE in which could provide additional status information of device drives (Detail refer to chapter 3). Fig 2-6: DA-BP4 series Back Plane Board ASUS AP5000 Installation Guide 11 II. BARE-BONE KITS SLOT CARD The ASUS slot card is DA-BC68 which uses for wide SCSI. Its jumpers and connectors are shown on Fig:2-7. It will setup with Hot-Swap drive bay. KEY SLED PLED ALED_IN SCSI_ID II. BARE-BONE KITS (This page was intentionally left blank) II. BARE-BONE KITS 14 ASUS AP5000 Installation Guide III. INTEGRATION PROCEDURES Along with previous product shipping kits, this section will introduce you on how to integrate an AP5000 together, and some of the notices you need to be aware of during installation. The step-by-step procedures have divided to five topics which are System Unit Integration, CPU Card Installation, Cabling, Device Drives, Installation, and Back Plane Board Installation. SYSTEM UNIT System assembly steps are as follows: 1. [. . . ] Below will show the DA-BP4-1(S) with the box. IDSEL 3/2/1/0 SCSI ID 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ID3 off off off off off off off off on on on on on on on on ID2 off off off off on on on on off off off off on on on on ID1 off off on on off off on on off off on on off off on on ID0 off on off on off on off on off on off on off on off on III. Integration Back Plane Board 26 Fig 3-30: Front-Site View of DA-BP4-1(S) & Switches Specification Per Back Plane Board contains 4 slots to support 4 SCSI drives and it will connect to Slot Card of Drive Bay. Fig 3-31: Back-Site View of DA-BP4-1(S) Fig 3-32: DA-BP4-1(S) with Box together ASUS AP5000 Installation Guide III. Integration Procedures Integrating with the housing The housing could carry two Back Plane Boards to support eight SCSI drives in total, and the first Back Plane Board has to be placed on lower position of housing (Fig 3-33) and its two notches should connect to the openings housing with no space in between (Fig 3-34), so that it could enlarge the force while inserting the drive bay. The second Back Plane Board also has to use similar method mentioned above for the connection. [. . . ]